Specifications:

  • Brand New Suspension & Steering Kit
  • Comes as a Set of 10
  • Fits LH (Driver Side) & RH (Passenger Side) Front
  • Direct replacements
  • Built to strict quality control standards

Our steering and suspension components come pre-greased, sealed for long life, and do not require the extra maintenance typically required by greasable versions.

Direct Fit

Application-specific, with no modifications required.

Rigorously Tested

Made from higher quality materials than the competition. Built to have a longer life in any environment or road conditions.

State of the Art Manufacturing

By the same factories that the OEMs use.

Prepackaged for Your Convenience

Carefully assembled to include all of the parts you need, saving time and money.

Part Details

  • Kit Includes: (2) Front Lower Ball Joints
  • Kit Includes: (2) Front Upper Control Arms with Ball Joints
  • Kit Includes: (2) Front Outer Tie Rods
  • Kit Includes: (2) Front CV Axles
  • Kit Includes: (2) Front Inner Tie Rods
  • Quantity: 10 Piece Set

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

Please Note: Whenever replacing steering components, it is highly recommended to have a professional alignment performed on the vehicle afterwards.  Failure to do so may result in issues with steering and premature tire wear.

  1. step : Removing the Wheel (0:40)
    • Loosen the lug nut covers
    • Pry off the center cap with a flat blade screwdriver
    • Loosen the lug nuts with the vehicle on the ground
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the lug nuts
    • Pull off the wheel
  2. step : Removing the Tie Rod (1:00)
    • Measure from the boot to the outer tie rod and record it
    • Loosen the 19mm nut on the tie rod with a 19mm wrench
    • Remove the cotter pin with pliers
    • Remove the castle nut with a 17mm socket
    • Hit the knuckle with a hammer
    • Twist the tie rod out
  3. step : Installing the New Tie Rod (2:13)
    • Twist on the new tie rod
    • Push the outer tie rod down into the knuckle
    • Replace the castle nut
    • Push the cotter pin into place and bend the ends in separate directions with pliers
    • Measure and double check the distance of the boot to the tie rod
    • Turn the tie rod joint with the 14mm wrench to adjust the distance
    • Replace and tighten the 19mm nut
  4. step : Reattaching the Wheel (3:15)
    • Slide the wheel into place
    • Start the lug nuts by hand
    • Tighten the lug nuts preliminarily
    • Lower the vehicle to the ground
    • Tighten the lug nuts to between 100 foot-pounds in a crossing or star pattern
    • Reattach the center cap

Tools needed for replacement:

    General Tools

  • Hammer
  • Jack Stands
  • Floor Jack

  • Pliers, Cutters & misc Wrenches

  • Needle nose pliers

  • Ratchets & Related

  • Torque Wrench
  • Ratchet

  • Sockets - Metric

  • 17mm Socket
  • 19mm Socket

  • Wrenches - Metric

  • 14mm Wrench
  • 19mm Wrench

5.0 / 5.0
1 Review
5 Stars
4 Stars
3 Stars
2 Stars
1 Star
1
0
0
0
0
Great kit,Great price.
My original lower ball joint did not have a c clip the new ones did. With a brake job it took me about 2 days,axles went in like butter when I put grease on the end,Thanks.
July 26, 2017
Purchased
1 year ago
Start typing your question and we'll check if it was already asked and answered. Learn More
Browse 3 questions Browse 3 questions and 5 answers
These fit 2000 civic si?
Adam M on Aug 25, 2016
BEST ANSWER: Yes, according to the information you supplied, the part you���re looking at will be correct for your vehicle. If you have any other questions or would like to place an order with one of our customer service representatives, please feel free to give us a call.
Hey there I have a Honda Civic ex 1996 do you think that they will fit my car perfectly?
Ayme T on Dec 30, 2016
BEST ANSWER: Yes, these parts are guaranteed to fit your 1996 Honda Civic EX without any modifications.
What is the length of both CV axles?
N Q on Mar 20, 2016
BEST ANSWER: We don't have the exact measurements. Our parts are designed to be exact replacements for what came with the vehicle, so as long as your year, make, and model match up with our listing, these will definitely fit and function just like the original. Please let us know if you have any other questions.

Vehicle Fit

  • 1996-1998 Honda Civic 10 Piece Set Steering & Suspension Kit
  • 1999-2000 Honda Civic (excluding SI Models) 10 Piece Set Steering & Suspension Kit

This part replaces:

  • A1 Cardone 66-4060
  • A1 Cardone 66-4064
  • Dorman 520-669
  • Dorman 520-670
  • OE # 53560S04013, 53560S04013
  • OE # 53540S04013, 53540S04003
  • Moog K9802
  • Moog ES3332R
  • Moog ES3331R
  • Moog EV367
  • Moog K90451
  • Moog K90450
  • Reference Number GSP NCV36045
  • Hollander 511-58112L
  • Hollander 511-58112R
  • OE # 51460-S01-023
  • OE # 51450-S01-023
Part #: 1ASFK02396

How-to Video:

(03:54 min)