Honda Civic Steering, Suspension, & Brake Kit - 1ASFK05646


Please Note: Whenever replacing steering components, it is highly recommended to have a professional alignment performed on the vehicle afterwards.  Failure to do so may result in issues with steering and premature tire wear.

Positive Mold Technology

Positive Mold Technology improves durability and performance by allowing for even wear. High density, low resin friction material virtually eliminates brake fade and glazing, generates less brake dust, and promotes a longer-lasting , better performing brake pad.

Thermal Scorched

Pre-burnishing or "Thermal Scorching" is the final curing step in quality ceramic brake pad manufacturing. The brake pad's surface is heated to remove any uncured bonding agents and to stabilize the friction material to accelerate the break-in process and enhance stopping performance from the first stop.

Direct Fit

All parts are direct fit, application-specific parts with no modifications required

Rigorously Tested

Rigorously tested and made from higher quality materials than the competition. Our parts are built to have a longer life in any environment or road conditions.

State of the Art Manufacturing

Our parts are manufactured by some of the same factories that the OEMs use.

Prepackaged for Your Convenience

Our kits have been carefully put together to include all of the parts you need to get the job done, saving you both time and money. These kits also help take the guesswork out of finding the correct part for your vehicle’s steering or suspension system, allowing you to get started on your repair project faster.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

    We recommend an alignment after completing this repair

  1. step : Removing the Wheel (0:49)
    • Loosen the 19mm lug nuts with the vehicle on the ground
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the lug nuts
    • Pull off the wheel
  2. step : Removing the Outer Tie Rod (1:20)
    • Loosen the 24mm lock nut with a 21mm wrench and hammer
    • Make note of how far you turn the inner tie rod to turn it back for reinstallation
    • Remove the 24mm nut from the outer tie rod end
    • Remove the cotter pin with needle nose pliers
    • Remove the ball joint nut
    • Strike the steering knuckle with a hammer to loosen the outer tie rod
    • Twist off the outer tie rod by hand
  3. step : Installing the New Outer Tie Rod (3:27)
    • Twist the new outer tie rod onto the inner tie rod
    • Push the outer tie rod into the steering knuckle
    • Fasten the castle nut onto the outer tie rod
    • Tighten the castle nut to 32 foot-pounds
    • Push the cotter pin through the castle nut
    • Twist the cotter pin into place with needle nose pliers
    • Make sure the inner tie rod is in its correct position
    • Hold the tie rod with an 18mm wrench
    • Tighten the 24mm lock nut
  4. step : Reattaching the Wheel (5:32)
    • Slide the wheel into place
    • Start the lug nuts by hand
    • Tighten the 19mm lug nuts preliminarily
    • Lower the vehicle to the ground
    • Tighten the lug nuts to 80 foot-pounds in a crossing or star pattern

Tools needed for replacement:

    General Tools

  • Hammer

  • Materials, Fluids, and Supplies

  • Rust Penetrant

  • Pliers, Cutters & misc Wrenches

  • Needle nose pliers

  • Ratchets & Related

  • Ratchet
  • Torque Wrench
  • 1/2 Inch Breaker Bar

  • Sockets - Metric

  • 24mm Socket
  • 17mm Socket

  • Wrenches - Metric

  • 21mm wrench
  • 24mm Wrench

There are no reviews for this item. Write Review
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

  • 2001 Honda Civic 21 Piece Set Steering, Suspension, & Brake Kit
  • 2002 Honda Civic excluding SI Models 21 Piece Set Steering, Suspension, & Brake Kit
  • 2003-2005 Honda Civic L4 1.7L Automatic Transmission excluding SI Models 21 Piece Set Steering, Suspension, & Brake Kit

This part replaces:

  • OE # 51350S5A306
  • Hollander 447-59759L
  • Hollander 538-58878A 538-58878B
  • OE # 52320S5A013
  • Moog K640288
  • OE # 51321SCVA91
  • OE # 51360S5AA20
  • OE # 53541S5A003
  • OE # 45251S6DE10
  • OE # 44305S5DA61
  • OE # 52321S5A013
  • Moog K90332
  • OE # 51350S5AA20
  • OE # 51350S5AA02
  • Moog K90453
  • OE # 51360S5AA02
  • OE # 51350S5AA10
  • Hollander 447-60888R
  • OE # 51350-S5A-A20
  • A1 Cardone 66-4189
  • Dorman 520-925
  • OE # 51321S5A003
  • OE # 51350S5AA03
  • OE # 51360-S5A-A20
  • OE # 51320SCVA91
  • OE # 51360S5AA03
  • OE # 51360S5AA10
  • Hollander 512-58745L
  • OE # 51220S5A003
  • OE # 44600S5AJ00
  • OE # CC900
  • Hollander 512-58744R
  • OE # 6469159
  • OE # 44300S5A008
  • OE # 53521S5A003
  • Moog EV469
  • OE # 51321-S5A-003
  • OE # 44600S5DA00
  • OE # 51320-S5A-003
  • Dorman 930-456
  • Moog K90454
  • OE # K7A00
  • Moog K90452
  • OE # 51320S5A003
  • Dorman 520-926
  • Moog K640287
  • OE # 51360S5A406
  • Moog ES3581
  • Moog K90455
Only 4 left in stock
Part #: 1ASFK05646

How-to Video:

(06:17 min)