Honda Accord Steering & Suspension Kit 16 Piece Set TRQ PSA56181 - 1ASFK01871

Frequently bought together

Warranty & Shipping
How-To & Tools
Product Reviews
Vehicle Fit

Part Details

  • Quantity:   16 Piece Set
  • Kit Includes:
      (2) Front Lower Ball Joints
      (2) Front Upper Control Arms with Ball Joints
      (2) Front Lower Control Arms
      (2) Front Outer Tie Rods
      (2) Rear Strut & Spring Assemblies
      (2) Front Sway Bar Links
      (2) Front Strut & Spring Assemblies
      (2) Front Inner Tie Rods


  • 16 Piece Suspension Kit includes:
    • (2) - FRONT Strut & Spring Assemblies - LH (Driver Side) & RH (Passenger Side)
    • (2) - REAR Strut & Spring Assemblies - LH (Driver Side) & RH (Passenger Side)
    • (2) - FRONT UPPER Control Arms - LH (Driver Side) & RH (Passenger Side)
    • (2) - FRONT LOWER Control Arms - LH (Driver Side) & RH (Passenger Side)
    • (2) - FRONT LOWER Ball Joints - LH (Driver Side) & RH (Passenger Side)
    • (2) - FRONT OUTER Tie Rod Ends - LH (Driver Side) & RH (Passenger Side)
    • (2) - FRONT INNER Tie Rod Ends - LH (Driver Side) & RH (Passenger Side)
    • (2) - FRONT Sway Bar Links - LH (Driver Side) & RH (Passenger Side)
  • Parts are new, not remanufactured or refurbished
  • Direct replacements
  • Built to strict quality control standards

Should You Purchase This Steering & Suspension Kit for Honda Accord? 

Refresh the whole suspension on your Honda Accord with this 16 piece steering and suspension kit. Steering and suspension parts can wear out over time, making your ride bouncy and your steering loose and sloppy. So, if your Honda's seen a lot of years and miles why not refresh your whole suspension and get your car riding like new? This kit has the upper and lower control arms, ball joints, inner and outer tie rod ends, sway bar links and front and rear struts, guaranteed to fit 1994 Honda Accords and 1995-1997 Accords with the 2.2 liter engine.

These aftermarket suspension parts are built to the same specifications as the original equipment and rigorously tested for durability. That's why they're backed by a lifetime warranty against manufacturing defects.

A kit like this one is convenient and cost-efficient because it saves you the trouble of tracking down each part. You can trust that all these parts will fit your Accord. The direct fit also makes for a straightforward install. You may need to support the car and remove the wheels to get better access to the suspension. You’ll want to measure the old parts before installing the new ones, so you can set them properly. Then, unbolt the parts and bolt on the new ones. You should always get a professional alignment after working on your steering. You can see a video showing the process for the tie rods in the "How-To & Tools" tab.

Our steering and suspension components come pre-greased, sealed for long life, and do not require the extra maintenance typically required by greasable versions.

Direct Fit

Application-specific, with no modifications required.

Rigorously Tested

Made from higher quality materials than the competition. Built to have a longer life in any environment or road conditions.

State of the Art Manufacturing

By the same factories that the OEMs use.

Prepackaged for Your Convenience

Carefully assembled to include all of the parts you need, saving time and money.

Item Condition: New

Attention California Customers:

WARNING:  This product can expose you to chemicals including Chromium (Hexavalent Compounds), which is known to the State of California to cause cancer, and birth defects or other reproductive harm.  For more information, go to

Lifetime Warranty

This item is backed by our limited lifetime warranty. In the event this item should fail due to manufacturing defects during intended use, we will replace the part free of charge.

Note: When replacing steering components, it is recommended to have a professional alignment performed on the vehicle afterwards. This will ensure proper tracking and even tire wear.

  1. step : Remove the wheels (1:00)
    • Loosen the lug nuts
    • Raise and secure the vehicle
    • Remove the wheel
  2. step : Remove the tie rod (1:32)
    • Mark the alignment on the tie rod with a sharpie.
    • Use two wrenches to loosen up the tie rod nut.
    • Remove the cotter pin and remove the 16 mm nut.
    • Use a tie rod puller to pry out the tie rod.
    • Unscrew the tie rod.
  3. step : Install the new tie rod (4:05)
    • Adjust the new locking nut to the same spot that the old one was (where you made your mark)
    • Screw in the new tie rod.
    • Install the cotter pin and bolt on the 17mm nut.
    • Install the cotterpin.
    • Use a grease gun to fill the joint.
  4. step : Replace the wheel (7:15)
    • Put the wheel on and hand tighten the lug nuts
    • Lower the car and torque the lug nuts to 80 ft lbs.

Tools needed for replacement:

    General Tools

  • Floor Jack
  • Jack Stands

  • Materials, Fluids, and Supplies

  • Marker / Writing Utensil

  • Pliers, Cutters & misc Wrenches

  • Adjustable Wrench
  • Needle nose pliers

  • Ratchets & Related

  • 1/2 Inch Breaker Bar
  • Ratchet
  • Torque Wrench

  • Sockets - Metric

  • 16mm Socket
  • 17mm Socket
  • 18mm Socket
  • 19mm Socket

  • Specialty Tools

  • Grease Gun
  • Tie Rod Puller

There are no reviews for this item.
Will this fit my car? Add a vehicle to make sure
Customer Q&A
Ask a question to 1A Auto customers who purchased the product
This is adjustable??
Justin B June 27, 2017
No, these are not adjustable.
Tim K June 27, 2017
What brand is this? Or is this actually made by you?
Justin B June 29, 2017
This is our 1A Auto brand set and built to meet or exceed the OE specifications. We also back them with a lifetime warranty.
Alex P June 29, 2017
What brand are the shocks?
William G October 24, 2017
We have a few different aftermarket companies build these parts specifically for us, as our 1A Auto house brand. They are manufactured to the same OEM specifications as the original part that came with your vehicle. If you have any further questions, please dont hesitate to ask.
Alex P October 24, 2017
Does this fit a 95 Accord EX 2.2L?
Amauris P May 14, 2018
Yes, according to the information you supplied, the part youre looking at will be correct for your vehicle. If you have any other questions or would like to place an order with one of our customer service representatives, please feel free to give us a call.
Peter L May 14, 2018
Will this kit fit on 1995 Honda Accord lx 2.7 v6?
Demetrick W September 29, 2018
Some of the kit will fit your V6 model, but some pieces wont.
Tim K October 1, 2018
Does the suspension kit lower the stock ride height at all? On the 96 accord?
Adam K August 4, 2019
Thanks for your inquiry. This kit is correct for the 1996 Honda Accord L4 2.2L. These parts are made to the same specifications as the originals, and you should expect the ride height to be the same as well. The installation is pretty straightforward. You can see a video showing the process for the tie rods in the "How-To & Tools" tab on the listing. Please let us know if you have any other questions. Thank you!
Katie L August 5, 2019
Year Make Model Description
1994Honda Accord Honda Accord Steering & Suspension Kit 16 Piece Set
1995-1997Honda Accord Honda Accord L4 2.2L Steering & Suspension Kit 16 Piece Set
Part 1ASFK01871
In Stock

Order must be placed by 4pm ET
Delivery options for:

Estimated Arrival Cost

Deliveries made to PO Boxes and FPO may take longer. See our Shipping & Delivery for more information.

Brand #: PSA56181