Replaces
Frequently bought together
Assemblies may include halogen or incandescent test bulbs that should be replaced before installation.
Item Condition:
New
Attention California Customers:
WARNING: This product can expose you to chemicals including Chromium (Hexavalent Compounds), which is known to the State of California to cause cancer, and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov
This item is backed by our limited lifetime warranty. In the event this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.
The bulbs are for testing and not covered under our warranty. Our warranty applies to the light assembly only.
FREE Shipping is standard on Orders shipped to the lower 48 States (Contiguous United States). Standard shipping charges apply to Hawaii, Alaska and US Territories. Shipping is not available to Canada.
Expedited is available on checkout to the United States, excluding Alaska, Hawaii and US Territories as well as P.O. Boxes and APO/FPO/DPO addresses. Final shipping costs are available at checkout.
Created on:
Tools used
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet. Hi, I'm Mike Green. I'm one of the owners of 1A Auto. I want to help you save time and money repairing and maintaining your vehicle. I'm going to use my 20 plus years experience restoring and repairing cars and trucks like this to show you the correct way to install parts from 1A Auto.com. The right parts installed correctly. That's going to save you time and money. Thank you and enjoy the video.
In this video we're going to show you how to replace the third brake light on this 2000 Chevy S-10 Blazer. It's similar for many different GM vehicles. Tools you will need for this vehicle are a Phillips screwdriver, a regular screwdriver or a putty knife and possibly some type of wire cutters or razor blade or something to cut a rubber grommet. We do apologize a little bit in advance as we're doing this in winter so you can hear the heat in the background in the garage. Obviously the third brake light is right up on top of your vehicle. You can see I'm standing right on the back bumper. There are two Phillips screws. Remove those screws. I'm going to take a sock here and put it down so I'm less likely to scratch my paint. I'm going to use a putty knife. I'm fast forwarding a little bit. Just use that putty knife to break the seal between the light and the body of the car.
You can see here's the harness. To unplug your harness I'm going to start from the outside and pull down on this trim panel. Then you can see this is pull down on this. This red right here is my connection for the third brake light. Here's the connection. See our red and black wire. I'm just going to take a screwdriver, pry that tab up and disconnect it. Now I'm going to take a piece of thin gauge wire and just wrap it right around here. You can use string or whatever for this part. You just want to put something on there to follow it up so as I pull my harness out it pulls the wire with it. Back up on top here, lightly pull through. There's my wire out. Now I'm going to use that sock and a little household cleaner like some Windex or whatever, a paper towel.
Here's our new light and the old light. The new light all the same; a little shinier. The new light is designed to fit a number of different applications so it actually comes with adapter harnesses so you basically want to choose the correct one which for this vehicle it would be this one. Then for some applications there is a rubber grommet installed. This vehicle does not require this so I'm going to use a pair of wire cutters and actually cut this grommet off carefully. I'm going to fast forward through this. There's a number of ways you can cut this off. These wire cutters are probably the safest, but obviously you could use a razor blade or even a serrated house knife. Obviously be very careful not to cut your fingers or the wires.
Now I'm just going to take these two, wrap my piece of wire around them just like before and put them down into the hole. I'm going to slowly, carefully pull them through. Now I can put on my harness. Plug it in. Then remove the guide wire. Put all that up inside. Before we install we want to remove the adhesive. Tear it to get around the wiring right there. Then what I like to do is put the screws through and make sure that the wire goes down in there and the screws hit there and the screw first and put it down in. Then tighten up your screws.
We hope this helps you out. It was brought to you by www.1AAuto.com your source for quality replacement parts and the best service on the internet. Please feel free to call us toll free 888-844-3393. We are the company with you on the internet and in person.
Tools used
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.
Hi, I'm Mike from 1A Auto. I hope this how-to video helps you out, and next time you need parts for your vehicle, think of 1AAuto.com. Thanks.
In this video, we're going to show you how to replace the third brake light on this 1996 Chevy Tahoe. The items you'll need for this is a new third brake light from 1AAuto.com and a Phillip's screwdriver.
Start off by prying out this panel. It's held in with two clips: one right here, and another one in the same spot on the other side. Right here, this yellow and black harness is the one to your third brake light. Just pull back on that tab and pull it free. Your third brake light is held in with two Phillip's screws: one right here and one right there. We'll just fast forward as Don removes those. Now, pull the light up and out.
Up front is the old third brake light, and behind it is the new one from 1A Auto. You can see they're identical, and they'll mount exactly the same. Just detach your harness by pushing those wires into place. Because this third brake light is for several different vehicles it does have this grommet here that you don't need. Using a razor blade just cut it into a square shape. Just feed that wire down into that hole, remove the adhesive strip covers, and push the third brake light down into place. Once you have it in place, just replace those two Phillips screws. Now, reconnect your harness and replace this panel by just feeding it up underneath the side panels. Then, just line it up and hit it into place. You're all set.
We hope this video helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.
Tools used
I'm gonna take these two screws out, just use a Phillips head screwdriver. Take that screw out. Just slide the light straight back. And it's gonna be a little bit tight right there. Disconnect the connector, slide this out and slide it off. This rubber piece has to come off. Just slide this out of here. We can reuse that. Take this, slide this into the new light assembly. And that looks good. All right. Connect the connector. Put this back in position. Kind of helps if you angle it a little bit. Push that rubber piece all the way through. And that's good. And put the screws back in. And snug those up.
