This heater blower motor with fan cage is a new, aftermarket replacement part. It is just what you need to bring your heating and A/C blower system back to good working order!

Specifications:

  • New, not remanufactured or rebuilt
  • Includes blower motor fan cage impeller already installed
  • Direct replacement
  • Replaces dealer part numbers: 87103-0E040, 871030E040
  • Built to strict quality control standards
  • 100% tested prior to leaving the factory

If you are experiencing intermittent stopping during use, squealing noise from bearings, or poor air flow from your dash vents this may be your solution.

Our electrical and electronic parts are subject to strict quality control testing.  Once the item has been installed or plugged in, it is no longer eligible for a refund.  The item may be eligible for replacement, only if it is found to have a manufacturing defect. Before purchasing, please ensure proper diagnosis of the failed original part is performed

Left Hand Drive Note:

“All of our auto parts are intended for Left Hand Drive USDM vehicles and might not have been tested on Right Hand Drive platforms. If your vehicle is Right Hand Drive, please do your research prior to making a purchase to ensure the part is correct for your specific vehicle.”

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

  1. step : Removing the Blower Motor (0:20)
    • Remove the four clips from the panel below the glove box
    • Pull down the panel under the glove box
    • Disconnect the blower motor electrical connector
    • Remove the three 8mm bolts from the blower motor
    • Remove the blower motor from the HVAC box
  2. step : Installing the Blower Motor (3:27)
    • Lift the blower motor into the HVAC box
    • Insert the three 8mm bolts into the blower motor
    • Connect the blower motor electrical connector
    • Line up the panel below the glove box, using the locating tabs
    • Push the clips into the panel below the glove box

Tools needed for replacement:

    Ratchets & Related

  • Socket Extensions
  • Ratchet

  • Screwdrivers & Related

  • Phillips Head Screwdriver

  • Sockets - Metric

  • 8mm Socket

  • Specialty Tools

  • Trim Tool Set

5.0 / 5.0
1 Review
5 Stars
4 Stars
3 Stars
2 Stars
1 Stars
1
0
0
0
0
Vent blower
The video on how to replace the blower really helped. It took me longer to find my socket then it did to replace the blower.
The blower was simple to order and delivered in the time as requested.
I wish I would have replaced it a year ago! Nice having quiet ventilation.
November 20, 2017
Purchased
6 months ago
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

  • 2013 Lexus ES300h Heater Blower Motor with Fan Cage
  • 2007-2016 Lexus ES350 Heater Blower Motor with Fan Cage
  • 2010-2012 Lexus RX350 Heater Blower Motor with Fan Cage
  • 2010-2012 Lexus RX450h Heater Blower Motor with Fan Cage
  • 2010-2016 Toyota 4Runner Heater Blower Motor with Fan Cage
  • 2005-2016 Toyota Avalon Heater Blower Motor with Fan Cage
  • 2007-2017 Toyota Camry Heater Blower Motor with Fan Cage
  • 2008-2016 Toyota Highlander Front Heater Blower Motor with Fan Cage
  • 2007-2016 Toyota Tundra Heater Blower Motor with Fan Cage
  • 2009-2015 Toyota Venza Heater Blower Motor with Fan Cage

This part replaces:

  • Hollander 615-58674
  • OE # 87103-0E040
  • TYC 700215
Part #: 1AHCX00296

Ships Same Day for orders placed by 4 P.M. ET

How-to Video:

(04:56 min)