This blower motor with fan cage is a new, aftermarket replacement part. It is just what you need to bring your heating and A/C blower system back to good working order!


  • New, not remanufactured or rebuilt
  • Includes blower motor fan cage impeller already installed
  • Direct replacement
  • Replaces dealer part numbers: 87103-04021, 87103-17020, 87103-42020, NA01-61-B10, 8710304021, 8710317020, 8710342020, NA0161B10, MB657229
  • Built to strict quality control standards
  • 100% tested prior to leaving the factory

If you are experiencing intermittent stopping during use, squealing noise from bearings, or poor air flow from your dash vents this may be your solution.


Our electrical and electronic parts are subject to strict quality control testing.  Once the item has been installed or plugged in, it is no longer eligible for a refund.  The item may be eligible for replacement, only if it is found to have a manufacturing defect. Before purchasing, please ensure proper diagnosis of the failed original part is performed


Left Hand Drive Note:

“All of our auto parts are intended for Left Hand Drive USDM vehicles and might not have been tested on Right Hand Drive platforms. If your vehicle is Right Hand Drive, please do your research prior to making a purchase to ensure the part is correct for your specific vehicle.”

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

  1. step : Removing the Lower Dash Trim (0:22)
    • Remove the Phillips head screw from the trim
    • Press in the push clip and remove it from the dash
    • Remove the lower dash
  2. step : Removing the Blower Motor (1:10)
    • Disconnect the blower motor resistor
    • Remove the two Phillips screws from the resistor
    • Remove the resistor
    • Remove the wiring harness from the blower motor
    • Remove the screws from the blower motor
    • Pull the blower motor down and out
  3. step : Installing the Blower Motor (3:33)
    • Insert the blower motor into place
    • Tighten the Phillips screws to the blower motor
    • Connect the wiring harness to the blower motor
    • Insert the resistor into place
    • Tighten the two Phillips screws to the resistor
    • Connect the blower motor resistor
  4. step : Installing the Lower Dash Trim (5:05)
    • Insert the lower dash trim into place
    • Press the push clips into the lower dash
    • Tighten the Phillips head screws to the trim

Tools needed for replacement:

    Ratchets & Related

  • Socket Extensions
  • Ratchet

  • Screwdrivers & Related

  • Phillips Head Screwdriver

  • Sockets - Metric

  • 7mm Socket
  • 10mm Socket

  • Specialty Tools

  • Trim Tool Set

5.0 / 5.0
1 Review
5 Stars
4 Stars
3 Stars
2 Stars
1 Star
Blower fan
This part does what it needs to do. No complaints. It was fairly easy to install.
January 23, 2017
1 year ago
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

  • 1992-1996 Eagle Summit Wagon Heater Blower Motor with Fan Cage
  • 1990-1997 Mazda Miata MX-5 Heater Blower Motor with Fan Cage
  • 1992-1996 Mitsubishi Expo Heater Blower Motor with Fan Cage
  • 1992-2000 Mitsubishi Montero Heater Blower Motor with Fan Cage
  • 1992-1994 Plymouth Colt-Vista Heater Blower Motor with Fan Cage
  • 1991-1995 Toyota MR2 Heater Blower Motor with Fan Cage
  • 1992-1995 Toyota Paseo Heater Blower Motor with Fan Cage
  • 1989-1995 Toyota Pickup Heater Blower Motor with Fan Cage
  • 1996-2000 Toyota Rav4 Heater Blower Motor with Fan Cage
  • 1993-1998 Toyota T100 Heater Blower Motor with Fan Cage
  • 1991-1994 Toyota Tercel Heater Blower Motor with Fan Cage

This part replaces:

  • Partslink MI3126103
  • Hollander 615-58275 615-58214 615-58221
  • TYC 700039
  • DEPO 314-58006-100
Part #: 1AHCX00120

How-to Video:

(06:06 min)