Specifications

  • LH driver side
  • Includes lens, housing, mounting panel and gasket
  • Includes integrated parking/marker lamp
  • Bulbs not included
Direct Fit Replacement

Direct fit replacement for OEM assembly

Trouble-free Installation

Uses same wiring as original assembly.  No cutting or splicing required.

DOT and SAE Compliant

Meets federal regulations for on-road use

Item Condition: New

California Customers:

WARNING:  This product can expose you to chemicals including Chromium (Hexavalent Compounds), which is known to the State of California to cause cancer, and birth defects or other reproductive harm.  For more information, go to www.P65Warnings.ca.gov.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

Bulb Note:

Unless otherwise noted, our lights do not include bulbs, though occasionally lighting manufacturers do include bulbs in the lights. If you happen to receive a lighting product (Headlight, Tail light, parking light, fog light etc.) that comes with the bulbs, the bulbs are not covered under our warranty. Our warranty applies only to the light assembly..

    Note: DO NOT TOUCH the bulbs- the oil from your fingers will burn into the light and foul your bulb. Clean with rubbing alcohol and a soft cloth if the bulbs do get touched.

  1. step : To replace just the headlight bulbs (1:08)
    • Pop the hood and secure it.
    • Reach behind the headlight assembly.
    • Use a flat blade
    • Pull aside the rubber boot and unclip the retaining wire.
    • Remove and replace the bulb.
    • Anchor it with the retaining wire and seal it in with the rubber boot.
  2. step : Remove headlight (3:13)
    • Remove the four 10mm bolts securing the headlight assembly.
    • Use an 8mm socket and ratchet to remove the two bolts securing the washer bottle to access the bolts securing the headlight assembly easier.
    • On the driver’s side headlight, disconnect the negative battery cable and unbolt the fuse box to move it out of the way.
    • Use a 10mm socket and ratchet to do this.
    • Pull the headlight forward and out.
    • Disconnect the bulbs and wiring.
  3. step : Install the new headlight (5:20)
    • Plug in the wiring harness and bulbs.
    • Line up the assembly and bolt back in.
    • Bolt the grille back into place using your socket and ratchet.
  4. step : Aim the headlights (6:25)
    • Use a 4mm socket to adjust the headlights.
    • The low beam should be an inch below the height of the bulbs at 20 feet.
    • The high beams should be level with the bulbs at 20 feet.

Tools needed for replacement:

    Ratchets & Related

  • Socket Extensions
  • Ratchet

  • Screwdrivers & Related

  • Phillips Head Screwdriver
  • Flat Blade Screwdriver

  • Sockets - Metric

  • 10mm Socket
  • 8mm Socket

There are no reviews for this item. Write Review
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

Year Make Model Description
1996-1997Chrysler Town & Country Chrysler Town & Country Headlight Driver Side
1996-1999Dodge Caravan Dodge Caravan Headlight Driver Side
1996-1999Dodge Grand Caravan Dodge Grand Caravan Headlight Driver Side
1996-1999Plymouth Grand Voyager Plymouth Grand Voyager Headlight Driver Side
1996-1999Plymouth Voyager Plymouth Voyager Headlight Driver Side

This part replaces:

  • Partslink CH2502109
  • Hollander 114-361AL
  • TYC 20-3164-88-1
  • DEPO 333-1110L-AS
  • OE # 4857041AB
Part #: 1ALHL00435


Order must be placed by 4pm ET

Get it in: 2 - 4 Business Days

Want it sooner? Choose Next Day Air at Checkout

How-to Video:

(08:19 min)