Replaces
This part doesn’t fit a . Select from parts that fit.
Light Assembly Lifetime Warranty
Frequently bought together
Assemblies may include halogen or incandescent test bulbs that should be replaced before installation.
Features and Benefits
Item Condition:
New
Attention California Customers:
WARNING: This product can expose you to chemicals including Lead and Lead Compounds, which are known to the State of California to cause cancer, and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov.
This item is backed by our limited lifetime warranty. In the event this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.
The bulbs are for testing and not covered under our warranty. Our warranty applies to the light assembly only.
FREE Shipping is standard on Orders shipped to the lower 48 States (Contiguous United States). Standard shipping charges apply to Hawaii, Alaska and US Territories. Shipping is not available to Canada.
Expedited is available on checkout to the United States, excluding Alaska, Hawaii and US Territories as well as P.O. Boxes and APO/FPO/DPO addresses. Final shipping costs are available at checkout.
Created on:
Tools used
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the internet. Hi, I'm Mike Green, I'm one of the owners of 1A Auto. I want to help you save time and money repairing and maintaining your vehicle. I'm going to use my 20 plus years experience restoring and repairing cars and trucks like to show you the correct way to install parts from 1AAuto.com. The right parts installed correctly that's going to save you time and money. Thank you and enjoy the video.
In this video, we're going to show you how to replace the fog light on this 2002 GMC Sierra, this procedure is the same for any 2000 to 2006 Yukon or Yukon XL and '99 to '02 Sierra. The only tool you'll need is a 10 mm socket and ratchet or wrench. The common issue with these trucks is the fog lights get wiped out, like this one is here so we'll show you to replace them. The nice thing about these trucks is you don't have to jack them up or anything. I do have this up on a lift just to make it a whole lot easier to video but you're going to look right up underneath. First, you can disconnect your harness, just by pulling up on a little tab right here and then back, and then there's two 10 mm bolts up on top. Let's see if I can get to them. You remove this one here and there's one closer to the outside.
Once you have it unbolted, just push it forward, push this dam forward a little bit and pull it down and out. Obviously here's the one for the truck, a nice new one and it will look a whole lot prettier. I need to get the bolts out of this old one first, just going to use a set of needle nosed pliers and I'm going to pry it up and out and then the next thing is you just want to use your old one to kind of preliminary aim the new one and all's you want to do is measure how far this is and set your new one to the same distance. All's you do is just crank up on this nut here until you kind of are at the same distance, a little bit more. Now you're ready to install. I put my bolt into the new one. Put it into place. Start our bolt here. Put our other bolt up in, just push them down, wiggle them a little bit and then start them in. Then use our wrench. Once it's tight, you can plug it back in and now we can see that the new light works just fine.
We hope this helps you out. Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the internet. Please feel free to call us toll free 888-844-3393. We're the company that's here for you on the internet and in person.
Tools used
And disconnect the fog light connector right here. Let's pull up on the tab and slide the connector back, just like that. Now, there's two bolts that go straight down. So, I'm gonna use a 10-millimeter ratchet wrench. You could always use a socket and a ratchet. Take these two bolts out, take that bolt out, and get that out. And just slide the assembly right out. See, that's where the bolts go, right on top. So, it's a good idea to replace the bulb when you're changing the fog light, putting the bulb in there. And take the new assembly, put it in position. It's always good to start this one first, makes it a little bit easier. And just tighten them up, and snug those up, plug the connector in, lock it in place. And if you need to adjust it, the adjuster is right here, you can tighten this up or loosen it. You're good to go.
This is going to be a general tutorial on how to aim your brand new TRQ headlamp assemblies. Okay. So, looking at your brand new TRQ headlamp assembly, you're going to see where your low beam is, and you'll see a little dot right in the center. And that is the access point. Okay? So, what we're going to do is we're going to mark that with an erasable marker, just so it's easier to see. Next, what we need to do is measure from the level ground up to this point and take note of that measurement. Now, we're just going to pull the car up to our wall. On our vehicle, we remember that the measurement was 28 inches for our access point. Your vehicle may be different, but that's where I'm going to put this tape, just above that 28 inches. We'll do the same on the other side. Okay. So, let's just back the vehicle up, straight back 25 feet from the wall. And now that we moved our vehicle 25 feet back from the wall, we're going to start with our measurement here. That's where the headlamp's center is. We're gonna go down 4 inches on the driver's side. On the passenger side, we have our line here. What we need to do is go down 2 inches. To adjust the driver's side, we're going to cover our passenger side headlamp. If you look at the backside of your headlamp assembly, you're going to see something that looks like this. This is the adjustment. Some of these headlight assemblies have one, two, or even more of them, but you should at least have one. This is how we're going to adjust the headlight beam. Now, we're going to lower the top part of the beam down to just below this line. When you turn the adjustment to the right, it brings the beam up. And if you turn it to the left, it'll bring the headlight beam down. And this is this way on most vehicles. Let's continue on to doing the passenger side. All right. We properly aligned our TRQ headlamp assemblies.
Okay. And on the quality TRQ headlamps for a pickup truck, the procedure's going to be the same. You're going to find your center dot, mark it, and then you'll measure from the level ground up to your dot. So, once your headlamps are properly adjusted, it'll be time to adjust your fog lamps. You'll notice on the driver's side, the focal point is all the way at the bottom right now. I would like to bring it up so it meets up with approximately the bottom of the focal point of the headlight. Some fog lamps have an adjuster, others don't. The ones that do have an adjuster, you would just turn the adjustment to the left or to the right to adjust the beam up and down to where it needs to be. Now, with your TRQ headlamps and fog lamps properly aligned, you can drive down the road safely.
Tools used
