Replaces

GMC Nameplate General Motors OEM 22761717 - GMBEE00062

Specifications:

  • Brand New GMC Grille Nameplate/Emblem
  • Grille Mounted
  • Chrome & Red Finish
  • Original equipment part
  • Snaps on
OEM Part

Genuine original equipment part (OEM) that was factory installed on your vehicle by the manufacturer.

Part Details

  • Color: Chrome & Red

Warranty

Please inspect this part carefully prior to installation and contact us with any questions BEFORE attempting to install it. Due to the nature of this part, our 60-day warranty covers exchanges only. Parts that have been installed, neglected, or modified in any way are not eligible for this exchange.

  1. step : Disconnecting the Battery (1:07)
    • Undo the tabs that secure the floor mat
    • Snap the plastic cover off of the seat rail
    • Remove the T20 Torx screw from the cover
    • Lift the cover from the floor
    • Disconnect the negative battery terminal with a 10mm socket and ratchet
    • Remove the terminal out of the way
  2. step : Removing the Sight Shield (2:15)
    • Pry up the six plastic retainer pins with a flat blade screwdriver
    • Remove the pins by popping up the sight shield
    • Remove the six T20 Torx screws along the top of the grille and bumper
  3. step : Removing the Wheel Well Liner (3:23)
    • Remove the two 10mm bolts securing the bottom of the bumper
    • Turn the wheel out of the wheel well
    • Remove the seven T20 Torx screws from the outer wheel well liner
    • Remove the eight plastic clips from the inner wheel well liner
    • Pull out on the bottom portion of the wheel liner
    • Remove the wheel liner
  4. step : Removing the Fender Flare (5:31)
    • Pry off the wheel speed sensor retainer from the wheel well
    • Remove the two push pins in the wheel well
    • Remove the six T20 Torx screws on the backside of the fender well
    • Remove the rear wheel well liner
    • Squeeze the backend of the clips with needle nose pliers
    • Remove the outer wheel well liner
  5. step : Removing the Bumper (7:45)
    • Disconnect the fog light wiring harness
    • Have an assistant hold the bumper
    • Remove the 7mm screw on each side of the fender well side of the bumper
    • Have an assistant hold the other side of the bumper
    • Pop the clips out on either end
    • Remove the bumper from the vehicle
  6. step : Removing the Grille Nameplate (8:40)
    • Compress the push tabs with needle nose pliers and pull down on the nameplate
    • Remove the badge straight and evenly
  7. step : Installing the Grille Nameplate (9:25)
    • Insert the tabs into place
    • Press the badge in until it clicks
  8. step : Installing the Bumper (9:45)
    • With the help of an assistant, insert the bumper into place
    • Snap the clips in on either end
    • Tighten the two 7mm screws to the bumper
  9. step : Reinstalling the Fender Flare (10:29)
    • Snap the fender flare into the fender holes
    • Insert the rear wheel well liner into place
    • Press on the push clips
    • Tighten the six T20 Torx screws to the liner
    • Reconnect the fog light wiring harness
  10. step : Installing the Wheel Well Liner (11:31)
    • Insert the inner wheel well liner into place
    • Install the eight plastic clips to the inner wheel well liner
    • Install the seven T20 Torx screws to the outer wheel well liner
  11. step : Reinstalling the Sight Shield (12:36)
    • Tighten the 10mm screws to the bottom of the bumper
    • Reinstall the six T20 Torx screws along the top of the bumper
    • Insert the sight shield into place
    • Press on the clips to the sight shield
  12. step : Reconnecting the Battery (13:20)
    • Keep your keys handy
    • Reconnect the negative battery terminal
    • Tighten the 10mm bolt
    • Insert the cover into place
    • Tighten the T20 screw to the cover
    • Reinstall the seat rail cover
    • Insert the floor mat into place and connect the pins

Tools needed for replacement:

    General Tools

  • Assistant

  • Pliers, Cutters & misc Wrenches

  • Side Cutters
  • Needle nose pliers

  • Ratchets & Related

  • Ratchet
  • Socket Extensions

  • Screwdrivers & Related

  • Flat Blade Screwdriver

  • Sockets - Metric

  • 7mm Socket
  • 10mm Socket

  • Torx Drivers & Sockets

  • T20 Torx Driver

  • Wrenches - Metric

  • 10mm Wrench

There are no reviews for this item. Write Review
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

  • 2007-2017 GMC Acadia Grille Mounted Chrome & Red Nameplate General Motors OEM 22761717
  • 2007-2014 GMC Yukon Grille Mounted Chrome & Red Nameplate General Motors OEM 22761717
  • 2014 GMC Yukon XL Grille Mounted Chrome & Red Nameplate General Motors OEM 22761717
  • 2007-2013 GMC Yukon XL 1500 Grille Mounted Chrome & Red Nameplate General Motors OEM 22761717
  • 2007-2013 GMC Yukon XL 2500 Grille Mounted Chrome & Red Nameplate General Motors OEM 22761717

This part replaces:

  • General Motors OEM 22761717
  • OE # 22761717
Only 2 left in stock
Part #: GMBEE00062

Brand #: 22761717

How-to Video:

(14:18 min)