GMC 6 Piece Lighting Kit DIY Solutions LHT04201

Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.

Hi, I'm Mike Green. I'm one of the owners of 1A Auto. I want to help you save time and money repairing or maintaining your vehicle. I'm going to use my 20-plus years experience restoring and repairing cars and trucks like this to show you the correct way to install parts from 1AAuto.com. The right parts installed correctly: that's going to save you time and money. Thank you and enjoy the video.

In this video, we'll be replacing a fog light on a 2004 GMC Sierra. These fit the 2003 to 2006 Sierra. This is a fairly easy project. It only requires a 10 millimeter socket and wrench and a 5/32 inch Allen wrench.

We're going to be switching back and forth from underneath and above. Here is your back of your fog light and you can see up in there, that's one of the bolts that holds it in. There's 2 bolts that bolt in from the top. Now don't get too excited here. It's not just 2 bolts. Pull it out, unplug it, plug it back in. It's actually more complicated than that. You're actually going to have to take apart the light from the bracket to be able to get it out of the truck. It's a little bit close quarters.

We're going to start by removing the 2 bolts. They're 10 millimeter bolts and there's room to get up in there. You'll see my big paws, I can get my hand and wrench up in there and remove those bolts. You basically just have to go right up in behind the bumper and you'll see me reach over further and I can get a hold of the other one. They're not too bad to get a hold of. Obviously I have it up on the lift which is nice but it's still, even laying on your driveway or whatever, you can get up in there.

Once you have that done, I'm going to show you the light off of the car here. What I want to show you is how to remove the light from the actual bracket. Basically you just use a screwdriver, a regular screwdriver and just kind of pry to the side. That comes out of there. Don't pry too hard. Then, on the other side it's just 2 pins and they come right apart. Now, going to go back on the car here. Just flip that back together real quick. We'll need to do that process later.

Back on the car here, now you've got to unbolt it so you can move it around a little bit, reach in there with your screwdriver and separate out that side. It takes a little bit of finagling when you're working in close quarters like that but eventually it'll pop out. From the other side, you can take it out. Now, your light is still connected to the bracket by the adjusting screw. If you have a broken light, yje adjusting screw is a 5/32 inch Allen screw. If your light's broken, what you can do is just mark the adjusting screw up near here it goes into the light and this gives you a reference point of where your light was aimed before. I can talk more about that later. Now, I'm just taking the light out of the back. We'll go back to the front view here and you just kind of turn the light to the side and it pulls out of the front and then the bracket comes right out nicely.

With it altogether, you can't do it like that but it's not too much of a pain to get it apart. Now, I'm just going to unplug the bulb so it doesn't end up getting damaged. What you want to do if you've got a new light is take it apart and you want to take the adjusting screw out and you just kind of pinch that clip and it pulls out of the bracket just like that.

To put it back together, you put your bracker up in there. You don't need to bolt it in at this point, just kind of put it up in there and hang it up in there. Take your light and if you got confused or whatever, you want to know, you're not sure which side it up, there's writing on the lense, that writing should obviously be right side up and then there's a little rectangular hole right below the light hole and that should be on the bottom. Now, you just kind of place the light in there and just get it into position. You don't have to worry about it too much and just kind of finagle it in there. There it is. Now, we'll go back underneath and your adjusting screw that you have, you just put it up in there and you can start it with your hand. This is just really the easiest way to do it and make sure you get that adjusting screw in there straight. You don't want to try and put in there crooked and strip that little plastic nut that it goes into and then you just start it in there and pretty soon that clip will work its way into the square hole. Obviously you want to make sure that it clips in the right way. The teeth have to be the certain way, they have to be into the narrow way so that it will clip. Once you get a certain distance, than you can just kind of push the clip up in. You can't do it too early because you'll bottom out the light on the bracket and you don't want that to happen. I just put my thumb up in there, push it in. It's all set. Just do the allen screw back to basically the same position as you had it before. Like I said, when you take it apart, you can before you take it apart, you can mark it up near that little round plastic nut there. Mark where it is and you can either use your original adjusting screw or you can mark the new adjusting screw and get it basically into the same position.

Now we're going to just rebolt it back in. Again, you can get your hands up in there pretty easy. Just want to make sure that you really push the bolts back down into the clips and make sure you get it right. You can see here I actually have a little problem with the second one. What I have to do is kind of reach up in there with a screw driver and just slide the clip back into the place. Like I said, just make sure, when you put those in, you push them down into place, get them going a few turns and then pull back out and make sure you got a good bite into the clips. Once they're up in there, tighten them up and then I'm just replacing the bulb and then hook up the harness and you're pretty much good. You might want to turn them on. Obviously make sure everything's working right. Aim them, make sure that they're not pointing up at the sky or anything like that but be on that and you're pretty much all set.

We hope this video helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.

This video is brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the internet. Hi, my name is Mike Green. I want to help you save time and money repairing your vehicle. I have 20+ years experience restoring and repairing cars and trucks. My company, 1A Auto, sells high quality replacement parts over the internet. In this video I will be showing you how to install these parts. By the end of this video, you will know how to install them and where to get them, and that is going to save you time and money. Thank you and enjoy the video.

In this video, we are going to replace the parking light on a 2004 Sierra 2500, which is basically the same as any 1999-'06 GMC Sierra. This is a pretty easy process, it doesn't require any tools. There is two pins that hold the headlight in, right there and there, and you'll twist those out and pull them up. Then the headlight basically comes right out and then once it is out, you can reach in behind and unplug the lights. They're basically just little teeth that you can pull with your thumb and they unplug. Then the parking light is actually snapped in. There is a little bracket that goes into the side there, and then a little piece that you squeeze and snap out there, and you can see it, switch hands here and I'll push on that tooth and the light will pop out.

Then you just pull it forward and twist out the bulbs, and you can now service either those bulbs or if you need to replace the whole parking light because it got damaged or broken, you can do that. Then to install is the reverse of the procedure, insert the harnesses and twist to lock in. Side marker light and you want to get the inside tooth in there first. Then you can see that at a little better angel here. That just presses right into that slot and locks in. Then you re-install your headlight. At this time, just to show you, you can service the headlight bulbs if you want to, just twist and pull them right out. That's the high beam, same thing with the low beam. They just twist and pull right out. If you were replacing that headlight, you can see that black bracket, you might be able to bolt that on to the new headlight or if you headlight assembly comes with that whole thing, then it just goes in that easily.

Just place the light back into place and use your pins, twist them into place and lock them and there you are. You've just replaced the parking light and we will do a quick test. The running lights, the low beams, high beams, and signals just to make sure and you see actually our side marker light is not working, so we will actually go back in and replace that small bulb and fix that side marker light.

We hope this helped you out and thank you very much. This video was brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the internet. Feel free to call us toll free, 888-844-3393, we are the company for you on the internet and there for you in person too. Thank you very much.