Description
Warranty & Shipping
How-To & Tools
Product Reviews
Q&A
Vehicle Fit

Part Details

  • Includes:   (1) Wire Stripper / Crimper Tool

This replacement electric fuel pump is just what you need to get your vehicle in good working order again!

Specifications:

  • Mounts in fuel tank
  • Complete module assembly
  • Replaces dealer part numbers: 25344814, 19177238
  • Outlets: 3
  • Assembly includes the following parts:
    • Electric Fuel Pump
    • Plastic module
    • Fuel sending unit
      • Rheostat Range: 40-250 Ohms
    • Float
    • Strainer
  • Built to strict quality control standards
  • Only fits models with the following engines as listed:
    • V6 4.3L

This electric fuel pump module assembly with sending unit is a great replacement and has good cost savings over a dealer unit.

Our electrical and electronic parts are subject to strict quality control testing. Please ensure proper diagnosis of this item before purchasing as the item cannot be returned once installed or plugged in.

This fuel pump includes a new electrical connector harness. You will need to remove your existing electrical connector and install the new connector provided in order to install your new fuel pump (instructions are included with the pump).

This fuel pump is not a universal fit item. Because your vehicle’s original connector is prone to failure due to corrosion, cracking, loose pin housings, and wire crimp issues, the OE manufacturer has changed the shape of the connector, requiring the install of a new electrical connector during fuel pump service.

Rigorously Tested

Meets or exceeds all SAE fuel pump performance and durability standards

Highest Quality Material

Consistent high quality plastic molding media.

High-carbon motor commutator and brushes for longer pump life

Direct Fit Replacement

Guaranteed to fit and function correctly for your specific application

Item Condition: New

WARNING:  This product can expose you to chemicals including Di(2-ethylhexyl)phthalate (DEHP), which is known to the State of California to cause cancer, and birth defects or other reproductive harm.  For more information, go to www.P65Warnings.ca.gov.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

  1. step : Disconnecting the Fuel Pump Relay (0:45)
    • Turn the vehicle on and run the engine
    • Open the fuse box door
    • Locate and remove the fuel pump relay with pliers
    • Insert the fuel pump relay into the fuse box
    • Close the fuse box door
  2. step : Removing the Fuel Pump Panel (1:05)
    • Pull the back seats down
    • Pull the trim and carpet apart
    • Remove the 10mm bolts from the fuel pump panel
    • Pry up on the panel with a flat blade screwdriver
  3. step : Removing the Fuel Pump (2:07)
    • Pull up on the pin from the sending unit
    • Disconnect the sending unit wiring harnesses
    • Push the outside fuel lines in, push down on the tab, and pull them free
    • Push the tab on the center fuel line and pull it free
    • Hammer the locking ring with a flat blade screwdriver to turn the locking ring
    • Lift the locking ring up and off
    • Pull the fuel pump up
    • Let the pump drain
    • Lift the fuel pump up and out
  4. step : Preparing the Fuel Pump (3:55)
    • Apply the level sensor to the new fuel pump
    • Remove the fuel line clips from the old sensing unit
    • Remove the packing cap from the new fuel pump
    • Insert the fuel line clips onto the new fuel pump
    • Cut off the old sending unit wiring harness with the blue strip with wire cutters
    • Strip a quarter of an inch off the old wires with wire cutters
    • Apply the blue connectors on the grey and black wire
    • Apply the red connectors to the purple and black and white wire
    • Connect the new sending unit harness to the connectors
  5. step : Installing the Fuel Pump (7:39)
    • Place the fuel pump and sending unit into the fuel tank
    • Fit the locking ring into place and line up the slots with the tabs without pinching the harnesses
    • Twist the ring clockwise with a flat blade screwdriver and hammer
    • Remove one of the posts from the locking ring with a pair of pliers
    • Connect the pin to the sending unit
    • Connect the wiring harnesses to the fuel pump
    • Connect the fuel lines
  6. step : Reinstalling the Fuel Pump Panel (10:20)
    • Replace the panel
    • Insert and tighten the 10mm bolts
    • Cover the panel with the trim and carpet
    • Pull the back seats up

Tools needed for replacement:

    General Tools

  • Hammer

  • Pliers, Cutters & misc Wrenches

  • Wire Cutters
  • Wire End Cutters
  • Needle nose pliers

  • Ratchets & Related

  • Ratchet

  • Screwdrivers & Related

  • Flat Blade Screwdriver

  • Sockets - Metric

  • 10mm Socket

There are no reviews for this item.
Will this fit my car? Add a vehicle to make sure
Customer Q&A
Ask a question to 1A Auto customers who purchased the product
No questions have been asked about this item.
Year Make Model Description
1997-2001Chevy S10 Pickup Chevy S10 Pickup V6 4.3L Fuel Pump & Sending Unit Module with (1) Wire Stripper / Crimper Tool
2002Chevy S10 Pickup Chevy S10 Pickup V6 4.3L Crew Cab Fuel Pump & Sending Unit Module with (1) Wire Stripper / Crimper Tool for Models with Steel Tank
1997-2001GMC S-15 Sonoma GMC S-15 Sonoma V6 4.3L Fuel Pump & Sending Unit Module with (1) Wire Stripper / Crimper Tool
2002GMC S-15 Sonoma GMC S-15 Sonoma V6 4.3L Crew Cab Fuel Pump & Sending Unit Module with (1) Wire Stripper / Crimper Tool
1997-2000Isuzu Hombre Isuzu Hombre V6 4.3L Fuel Pump & Sending Unit Module with (1) Wire Stripper / Crimper Tool
Part #: 1AFPU01405


Order must be placed by 4pm ET

Get it in: 2 - 4 Business Days

Want it sooner? Choose Next Day Air at Checkout

How-to Video:

(11:21 min)