Replaces

Fuel Pump & Sending Unit Module TRQ FPA62021 - 1AFPU01344

 

Our electrical and electronic parts are subject to strict quality control testing. Please ensure proper diagnosis of this item before purchasing as the item cannot be returned once installed or plugged in.

Rigorously Tested

Meets or exceeds all SAE fuel pump performance and durability standards

Highest Quality Material

Consistent high quality plastic molding media.

High-carbon motor commutator and brushes for longer pump life

Direct Fit Replacement

Guaranteed to fit and function correctly for your specific application

Item Condition: New

WARNING:  This product can expose you to chemicals including Di(2-ethylhexyl)phthalate (DEHP), which is known to the State of California to cause cancer, and birth defects or other reproductive harm.  For more information, go to www.P65Warnings.ca.gov.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

  1. step : Removing the Fuel Pump Fuse Relay (0:53)
    • Open the fuse panel
    • Remove the fuel pump relay, located at the bottom right in the back passenger corner
    • Crank the car while pressing the gas pedal
  2. step : Disconnecting the Battery (1:40)
    • Loosen the 10mm nut on the negative battery terminal
  3. step : Removing the Rear Seat Cushion (2:00)
    • Feel the bracket underneath the rear seat and pull up firmly
    • Remove the lower seat cushion
  4. step : Removing the Fuel Pump and Sending Unit (2:17)
    • Lift up the rubber access door
    • Pop the harness cover out
    • Pop off the main cover
    • Disconnect the electrical connector
    • Release the lock ring with a screwdriver, chisel, or punch and hammer
    • Disconnect the fuel line and hoses
    • Lift the pump and O-ring sideways and let it drain
    • Disconnect the two-pin connector
    • Remove the assembly
    • Wipe off any spilled fuel in the compartment and on top of the tank
  5. step : Installing the Fuel Pump and Sending Unit (5:54)
    • Insert the lower half of the pump in at an angle
    • Once partially installed, connect the lines and fitting
    • Place the O-ring into place
    • Connect the connectors to the lid
    • Line the legs into the pump
    • Hold the top over the tank
    • Turn the lock ring as far as possible by hand
    • Tap the lock ring back into place
    • Press on the electrical connector
    • Reinstall the fuel pump lid
    • Reseal the harness boot
  6. step : Installing the Rear Seat Cushion (7:28)
    • Press on the back seat, push down, lock it in
  7. step : Reconnecting the Battery and Fuel Pump Relay (7:48)
    • Reconnect the negative battery terminal
    • Reinstall the fuel pump relay
  8. step : Priming the Fuel System (8:21)
    • Turn the key to the run position three times, allowing the fuel pump to run

Tools needed for replacement:

    General Tools

  • Hammer

  • Ratchets & Related

  • Ratchet

  • Screwdrivers & Related

  • Flat Blade Screwdriver

  • Sockets - Metric

  • 10mm Socket

5.0 / 5.0
2 Reviews
5 Stars
4 Stars
3 Stars
2 Stars
1 Star
2
0
0
0
0
Proud Customer!
Thank you 1AAuto! The fuel pump unit for my 2006 Chrysler 300 works amazing! I am very impressed with the quality and the price of this unit. I highly recommend others to visit 1AAuto when purchasing parts or comparing prices from other outside manufactures. I will continue to be a loyal customer of 1AAuto!!!
December 28, 2017
Purchased
9 months ago
2006 Dodge charger fuel pump
The part fit perfectly and works grate, thank you this is not the first time I've come to you for parts and I'm sure it won't be the last
March 26, 2017
Purchased
1 year ago
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

Year Make Model Description
2005-2010Chrysler 300 Chrysler 300 Rear Wheel Drive Fuel Pump & Sending Unit Module Driver Side for Models with 18 Gallon Tank TRQ
2009-2010Dodge Challenger Dodge Challenger Fuel Pump & Sending Unit Module Driver Side for Models with 18 Gallon Tank TRQ
2006-2010Dodge Charger Dodge Charger Rear Wheel Drive Fuel Pump & Sending Unit Module Driver Side for Models with 18 Gallon Tank TRQ
2005-2008Dodge Magnum Dodge Magnum Rear Wheel Drive Fuel Pump & Sending Unit Module Driver Side for Models with 18 Gallon Tank TRQ

This part replaces:

  • Airtex E7241M
  • Hollander 323-01929L
  • Spectra Premium Industries SP7048M
  • TRQ FPA62021
  • OE # 5136021AD
  • OE # 5136021AF
  • OE # 5136021AG
Only 5 left in stock
Part #: 1AFPU01344


Order must be placed by 4pm ET

Get it in: 2 - 4 Business Days

Want it sooner? Choose Next Day Air at Checkout

TRQ
Brand #: FPA62021

How-to Video:

(08:43 min)