These fuel injectors are just what you need to get your vehicle running great again!

Specifications:

  • Comes as a Set of 6
    • Brand New Fuel Injectors
  • Replaces dealer part numbers: 17120601, 17105121, 17105463, 17106772, 17113573, 17121105, 17121296
  • Built to strict quality control standards
  • Direct replacements
  • 100% factory tested

These fuel injectors are great replacements and offer good cost savings over the dealer units.

 

Our electrical and electronic parts are subject to strict quality control testing .  Once the item has been installed or plugged in, it is no longer eligible for a refund.  The item may be eligible for replacement, only if it is found to have a manufacturing defect. Before purchasing, please ensure proper diagnosis of the failed original part is performed

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

  1. step : Removing the Spark Plug Wires (0:46)
    • Unplug each of the spark plug wires - remember their order
    • Remove the spark plug wires from their clip
    • Remove the two vacuum hoses
    • Remove the 10mm bolts from the throttle body bracket
  2. step : Removing the Air Intake (1:47)
    • Loosen the air intake hose clamps with a flat blade screwdriver
    • Remove the air intake hose from the intake manifold
    • Disconnect the vacuum hose on the air intake hose
    • Disconnect the EGR harness
    • Remove the air intake hose from the air box
  3. step : Disconnecting the Intake Manifold (2:28)
    • Remove the two 13mm bolts from the throttle body
    • Remove the 10mm bolts from the top of the coil pack
    • Remove the 13mm bolts from the bottom of the coil pack
    • Slide back the hose clamp with a pair of pliers on the back of the intake manifold
    • Disconnect the hose
    • Remove the two 7mm bolts from the back of the MAP sensor
    • Disconnect the MAP sensor harness
    • Remove the sensor
    • Remove the hose with a flat blade screwdriver
    • Remove the two 10mm bolts from the EGR Valve
  4. step : Removing the Upper Intake Plenum (4:17)
    • Remove the 10mm bolts from the upper intake plenum
    • Remove the 13mm nut from the upper intake plenum
    • Remove the 10mm bolt below the right side of the intake manifold
  5. step : Disconnecting the Coolant Hoses (4:59)
    • Remove the cap on the radiator overflow bottle
    • Slide a drip pan underneath the drain plug
    • Remove the drain plug and drain the coolant
    • Pry off the coolant hoses
    • Remove the hoses from the top of the manifold
    • Replace and tighten the drain plug
  6. step : Disconnecting the Fuel Injectors (6:14)
    • Lift the upper intake plenum up and aside
    • Remove the intake gaskets
    • Disconnect the harness on the right side of the manifold
    • Remove the two 10mm bolts from the fuel injectors
    • Vacuum out the top of the engine
    • Carefully pry the fuel injectors up and out with a pry bar
    • Lift the fuel injectors out
    • Disconnect each fuel injector harness from its clip
    • Make sure the o-rings are on the fuel injectors
    • Lift and set the fuel injector aside
  7. step : Installing the Fuel Injectors (8:15)
    • Replace the clip on each injector
    • Place white grease on the edge of each fuel injector
    • Insert the fuel injector harnesses into place by their appropriate number
    • Line up the fuel injectors and push them down into the manifold
    • Replace the 10mm bolts on the fuel injectors
    • Connect the alternator harness
    • Connect the other harness on the other side of the manifold
    • Place the new gaskets on the intake manifold
  8. step : Installing the Coolant Hose (9:37)
    • Scrape off the old o-ring from the coolant tube
    • Place the new o-ring on the coolant tube
    • Push the hose into the manifold
  9. step : Installing the Upper Intake Manifold Plenum (10:02)
    • Replace the 10mm bolt below the right side of the intake manifold
    • Replace the 13mm nut on the lower part of the intake manifold
    • Insert the upper intake manifold plenum into place
    • Insert the 10mm bolts from the upper intake plenum
    • Insert the 13mm nut from the upper intake plenum
    • Torque the 10mm bolts to 18 foot-pounds
  10. step : Installing the MAP Sensor and Throttle Body (11:11)
    • Insert the two 7mm bolts from the back of the MAP sensor bracket
    • Connect the MAP sensor to the lead
    • Connect the sensor to the intake manifold
    • Tighten the 7mm bolts to the MAP sensor
    • Insert the 10mm bolts from the top of the coil pack
    • Insert the 13mm bolts from the bottom of the coil pack
    • Insert the hose and hose clamp on the back of the intake manifold
    • Insert the vacuum hoses to the intake manifold
    • Remove the rubber plug on the old manifold plenum to the new one
    • Tighten the two 13mm bolts from the throttle body
    • Tighten the 10mm bolts from the throttle body bracket
  11. step : Installing the EGR Valve (13:13)
    • Slide the hoses onto the coolant line
    • Tighten the hoses with the clamp and pliers
    • Place the gasket below the EGR
    • Insert the EGR and tighten the 10mm bolts
  12. step : Installing the Air Intake (14:24)
    • Loosen the air box with a Phillips screwdriver
    • Push the air intake hose into the throttle body
    • Tighten the Phillips screws on the air box
    • Tighten the air intake hose clamps with a flat blade screwdriver
    • Connect the vacuum hose on the air intake hose
    • Connect the EGR wiring harness
  13. step : Installing the Spark Plug Wires (15:54)
    • Clip in the spark plug wires clip
    • Plug each of the spark plug wires by number
  14. step : Refilling the Coolant (16:21)
    • Insert a funnel into the coolant bottle
    • Refill the coolant as needed

Tools needed for replacement:

    General Tools

  • Funnel
  • Drain Pan

  • Materials, Fluids, and Supplies

  • White Grease

  • Pliers, Cutters & misc Wrenches

  • Needle nose pliers

  • Ratchets & Related

  • Ratchet

  • Screwdrivers & Related

  • Pry Bar
  • Phillips Head Screwdriver
  • Flat Blade Screwdriver

  • Sockets - Metric

  • 13mm Socket
  • 10mm Socket

  • Specialty Tools

  • Vacuum

There are no reviews for this item. Write Review
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

How-to Video:

(16:49 min)

Tools List:

    General Tools

  • Funnel
  • Drain Pan

  • Materials, Fluids, and Supplies

  • White Grease

  • Pliers, Cutters & misc Wrenches

  • Needle nose pliers

  • Ratchets & Related

  • Ratchet

  • Screwdrivers & Related

  • Pry Bar
  • Phillips Head Screwdriver
  • Flat Blade Screwdriver

  • Sockets - Metric

  • 13mm Socket
  • 10mm Socket

  • Specialty Tools

  • Vacuum




Vehicle Fit

  • 1993-1995 Buick LeSabre Fuel Injector 6 Piece Set V6 3.8L
  • 1996-2000 Buick LeSabre Fuel Injector 6 Piece Set V6 3.8L (8th Vin Digit K)
  • 1998-2000 Buick Park Avenue Fuel Injector 6 Piece Set V6 3.8L (8th Vin Digit K)
  • 1995-1999 Chevy Camaro Fuel Injector 6 Piece Set V6 3.8L
  • 1994-1996 Chevy Caprice Fuel Injector 6 Piece Set V6 4.3L
  • 1993-1995 Chevy Lumina APV Fuel Injector 6 Piece Set V6 3.8L
  • 1996 Chevy Lumina APV Fuel Injector 6 Piece Set V6 3.4L
  • 1997-1999 Chevy Venture Fuel Injector 6 Piece Set V6 3.4L
  • 1999-2002 Daewoo Leganza Fuel Injector 6 Piece Set
  • 1999-2002 Daewoo Nubira Fuel Injector 6 Piece Set
  • 1999 Olds Alero Fuel Injector 6 Piece Set V6 3.4L
  • 1999 Olds Delta 88 Fuel Injector 6 Piece Set V6 3.8L (8th Vin Digit K)
  • 1996-1999 Olds LSS Fuel Injector 6 Piece Set V6 3.8L (8th Vin Digit K)
  • 1997-1998 Olds Regency Fuel Injector 6 Piece Set V6 3.8L (8th Vin Digit K)
  • 1993-1995 Olds Silhouette Fuel Injector 6 Piece Set V6 3.8L
  • 1996-1999 Olds Silhouette Fuel Injector 6 Piece Set V6 3.4L
  • 1996-2000 Pontiac Bonneville Fuel Injector 6 Piece Set V6 3.8L (8th Vin Digit K)
  • 1999 Pontiac Grand Am Fuel Injector 6 Piece Set V6 3.4L
  • 1999 Pontiac Montana Fuel Injector 6 Piece Set
  • 1993-1995 Pontiac Trans Sport Fuel Injector 6 Piece Set V6 3.8L
  • 1996-1998 Pontiac Trans Sport Fuel Injector 6 Piece Set V6 3.4L
Part #: 1AEEK00482

Out of Stock

We're here to help

1A Auto Parts

Customer Feedback

"Thanks for the fast reliable service. Great price, and the headlights were as good as oem or better!!! Keep up the good work..."
- Dwuan M.
Read More