These fuel injectors are genuine Mopar replacement parts! They are the very same pieces you would receive if purchased from your local dealer!


  • (8) - Brand New Mopar Fuel Injectors
  • Replaces dealer part number: 53032713AB
  • Built to strict quality control standards
  • Direct replacements
  • 100% factory tested
  • Correct for models with the following engines per application:
    • V8 5.7L

NOTE: Sold as a Set of 8 injector. For a single, please see our other listings.

Some symptoms of a bad fuel injector are: Stalling, hard starting, hesitation on acceleration, as well as a possible service engine light, and error code.

Your engine size can usually be found on a white sticker in the engine compartment near the radiator. If needed, your VIN code is the 8th digit of your vehicles Vehicle Identification number. The VIN can be found on the bottom driver side corner of the windshield and on your registration. Some refer to the VIN code as the Serial Number.


Now you can have genuine Mopar fuel injectors shipped right to your door!


Our electrical and electronic parts are subject to strict quality control testing.  Once the item has been installed or plugged in, it is no longer eligible for a refund.  The item may be eligible for replacement, only if it is found to have a manufacturing defect. Before purchasing, please ensure proper diagnosis of the failed original part is performed


OEM Part

Genuine original equipment part (OEM) that was factory installed on your vehicle by the manufacturer.

Part Details

  • Quantity: 8 Piece Set

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

  1. step : Disconnecting the Connector (0:47)
    • Find the connector behind the inner wheel well liner on the driver's side fender
    • Pry back the red safety
    • Lift up the gray latch
    • Open the fuel door
    • Remove the fuel cap
    • Start the truck so it dies
    • Keep cranking to run the system out of fuel
  2. step : Disconnecting the Battery (1:52)
    • Disconnect the negative battery terminal with a 10mm wrench
  3. step : Removing the Air Intake (2:00)
    • Release the clips and open the air filter housing box
    • List the air filter housing box cover up and off
    • Release the PCV hose
    • Loosen the rear clamp on the inlet pipe
    • Remove the box cover and pipe
    • Lift the bottom of the air filter housing box up and out
    • Remove the 10mm bolt behind the alternator
    • Remove the 10mm bolt behind the oil cap
    • Lift the air box up
    • Disconnect the intake sensor
    • Remove the air box
  4. step : Depressurizing the Fuel System (3:03)
    • On the passenger side fuel rail, remove the cap on the Schrader/pressure release valve
    • Place a paper towel below the valve
    • Press down the center of the valve with a pick to release the fuel pressure
  5. step : Removing the Fuel Injectors (3:46)
    • Remove the two 8mm bolts from the fuel rail
    • Clean any dirt or debris from the surrounding area to keep debris from falling in the injector holes
    • Pry up the red safety tab on the fuel injector
    • Push down and remove the connector from the injector
    • Pry out the retaining clip on the backside of the injector with a flat blade screwdriver
    • Evenly lift up the fuel rail, popping out one side at a time
    • Pull the fuel rail up and work the injector out of the fuel rail
  6. step : Installing the Fuel Injectors (5:54)
    • Lubricate the gasket on the fuel injector with a bit of gas from the rail
    • Insert the fuel injector into the fuel rail
    • Press the retaining clip on the back side
    • Press the rail into the manifold
    • Reconnect the injector wiring harness
    • Reinstall the two 8mm bolts
    • Screw the Schrader valve cap on
  7. step : Reinstalling the Air Intake (7:09)
    • Insert the air box with the silicone gasket over the throttle body
    • Tighten the two 10mm bolts to the box
    • Connect the air temp sensor
    • Insert the air filter housing into its mounting spots
    • Insert the intake tube to the air box
    • Tighten the hose clamp
    • Connect the PCV hose
    • Lock the air filter housing box
  8. step : Disconnecting the Connector (8:22)
    • Bring the latch on the connector back down
    • Reinstall the red safety tab
    • Reinstall the fuel cap
  9. step : Reconnecting the Negative Battery Terminal (8:44)
    • Tighten the 10mm bolt to the negative battery terminal
  10. step : Priming the Fuel System (9:09)
    • Turn the key to the on position
    • Turn the key off
    • Repeat the process three times
    • You might hear a high idle
    • Run the engine for a few seconds for the idle to drop to normal levels

Tools needed for replacement:

    General Tools

  • Pick

  • Materials, Fluids, and Supplies

  • Cloth Rags

  • Ratchets & Related

  • Ratchet
  • Socket Extensions

  • Screwdrivers & Related

  • Flat Blade Screwdriver

  • Sockets - Metric

  • 8mm Socket
  • 10mm Socket

There are no reviews for this item. Write Review
Start typing your question and we'll check if it was already asked and answered. Learn More
Browse 1 question Browse 1 question and 1 answer
How many lbs are these injectors rated for? 21lbs? 26lbs? 30lbs? ...
Jens H on Jun 26, 2018
BEST ANSWER: These are made to exact specifications as your originals.

Vehicle Fit

  • 2007-2008 Chrysler Aspen Fuel Injector 8 Piece Set V8 5.7L Mopar 53032713AB
  • 2004-2008 Dodge Durango Fuel Injector 8 Piece Set V8 5.7L Mopar 53032713AB
  • 2004-2008 Dodge Ram 1500 Truck Fuel Injector 8 Piece Set V8 5.7L Mopar 53032713AB
  • 2004-2008 Dodge Ram 2500 Truck Fuel Injector 8 Piece Set V8 5.7L Mopar 53032713AB
  • 2004-2008 Dodge Ram 3500 Truck Fuel Injector 8 Piece Set V8 5.7L Mopar 53032713AB

This part replaces:

  • Mopar 53032713AB
  • OE # 53032713AB
Only 1 left in stock
Part #: MPEEK00007

Brand #: 53032713AB

How-to Video:

(10:14 min)