Replaces

Ford Wheel Bearing & Hub Assembly Timken SP580205 - TKSHF00134

TIMKEN WHEEL BEARING & HUB ASSEMBLY: SP580205

This replacement hub & bearing assembly is just what you need to get your vehicle in good working order again.

Specifications:

  • Brand New Timken Wheel Bearing & Hub Assembly
  • Fits either LH (Driver Side) or RH (Passenger Side) FRONT
  • Replaces dealer part number: 3C34-2B513-BC, 3C342B513BC
  • 4 Bolt Flange
  • Fits 8 Lug Wheel
  • Includes ABS sensor
  • Studs already installed
  • Direct replacement
  • Built to strict quality control standards
  • Fine thread studs
  • Fits 4WD (Four Wheel Drive) Models only
  • Fits models with SRW (Single Rear Wheels)
  • Fits models with AWAL (4 Wheel Anti-Lock Brakes)

Note: These parts are authentic Timken brand products that are supplied and packaged by Timken.   In some cases, Timken will source parts from other high quality suppliers such as SKF and Koyo. These parts are subjected to the very same testing and quality standards as all Timken products.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

  1. step : Removing the Wheel (1:00)
    • Loosen the lug nuts with the vehicle on the ground
    • Remove the cotter pin from the axle nut if it has one
    • Loosen the axle nut
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the lug nuts
    • Pull off the wheel
  2. step : Removing the Brake Pads (3:22)
    • Remove the bolts from the caliper bracket
    • Pull the caliper off
    • Put the caliper aside
    • Pry the brake pads off with a flat blade screwdriver
  3. step : Removing the Brake Rotor (4:15)
    • Remove the two bolts from the caliper bracket
    • Pull off the brake caliper bracket
    • Remove a screw from the rotor if it has one
    • Strike the drum surface of the rotor with a hammer to loosen the rotor
    • Pull the rotor off
    • Clean the hub surface with a wire brush
  4. step : Removing the Hub Assembly (5:18)
    • Remove the axle bolt
    • Place a punch in the axle hole and hammer it to release the hub from the splines
    • Remove the bolts from the back of the hub
    • Remove the wheel hub and bearing
  5. step : Installing the Hub Assembly (7:53)
    • Insert the wheel hub into the spindle
    • Tighten the hub bolts
    • Reinstall the axle nut
  6. step : Installing the Brake Rotor (8:58)
    • Apply grease to the hub surface
    • Put the rotor onto the hub backwards
    • Spray the rear of the hub with brake cleaner
    • Pull off the brake rotor
    • Slide the brake rotor on
    • Spray the front of the rotor with brake cleaner
    • Put the caliper bracket into place
    • Insert the two into the caliper bracket
    • Torque the two bolts
  7. step : Installing the Brake Pads (9:48)
    • Put the brake pads into the caliper bracket
    • Apply grease to the back of the brake pads
    • Push back the caliper piston with grove lock pliers
    • Put the brake caliper into place
    • Insert the two bolts into the caliper
    • Torque the two bolts
  8. step : Reattaching the Wheel (11:01)
    • Slide the wheel into place
    • Start the lug nuts by hand
    • Tighten the lug nuts preliminarily
    • Lower the vehicle to the ground
    • Torque the lug nuts in a crossing or star pattern
    • Torque the axle nut

Tools needed for replacement:

    General Tools

  • Large C-Clamp
  • Chisel
  • Hammer

  • Materials, Fluids, and Supplies

  • Anti-Seize Grease

  • Ratchets & Related

  • Ratchet
  • Torque Wrench
  • Socket Extensions
  • 1/2 Inch Breaker Bar

  • Screwdrivers & Related

  • Flat Blade Screwdriver

  • Sockets - Metric

  • Complete Metric Socket Set

There are no reviews for this item. Write Review
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

Year Make Model Description
2002-2005Ford Excursion Ford Excursion 4 Wheel Drive 4 Wheel ABS Brakes Front Wheel Bearing & Hub Assembly Timken SP580205
2003-2004Ford F250 Super Duty Truck Ford F250 Super Duty Truck 4 Wheel Drive 4 Wheel ABS Brakes Front Wheel Bearing & Hub Assembly Timken SP580205
2003-2004Ford F350 Super Duty Truck Ford F350 Super Duty Truck 4 Wheel Drive 4 Wheel ABS Brakes with Single Rear Wheels (SRW) Front Wheel Bearing & Hub Assembly Timken SP580205

This part replaces:

  • Timken SP580205
  • Hollander 538-1494*
  • OE # 3C34 2B513 BC
Part #: TKSHF00134


Order must be placed by 4pm ET

Get it in: 2 - 4 Business Days

Want it sooner? Choose Next Day Air at Checkout

Timken
Brand #: SP580205

How-to Video:

(12:07 min)