Specifications:

  • Comes as a 4 Piece Kit:
    • Fits LH (Driver Side) & RH (Passenger Side)
  • Direct replacement
  • Built to strict quality control standards

Our steering and suspension components are sealed for long life and do not require the extra maintenance typically required by greasable versions.

Please Note: Whenever replacing steering components, it is highly recommended to have a professional alignment performed on the vehicle afterwards.  Failure to do so may result in issues with steering and premature tire wear.

Direct Fit

All parts are direct fit, application-specific parts with no modifications required

Rigorously Tested

Rigorously tested and made from higher quality materials than the competition. Our parts are built to have a longer life in any environment or road conditions.

State of the Art Manufacturing

Our parts are manufactured by some of the same factories that the OEMs use.

Prepackaged for Your Convenience

Our kits have been carefully put together to include all of the parts you need to get the job done, saving you both time and money. These kits also help take the guesswork out of finding the correct part for your vehicle’s steering or suspension system, allowing you to get started on your repair project faster.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

  1. step : Remove Wheel (1:09)
    • Remove hub nut
    • Remove lug nuts and remove wheel with an 18mm socket.
  2. step : Remove tie rod (1:50)
    • Remove cotter pin.
    • Use your 18 mm socket to remove the nut at the bottom of the tie rod.
    • Use your tie rod puller to pull the tie rod up.
    • Use your two adjustable wrenches to remove the tie rod.
  3. step : Remove the axle. (2:42)
    • Disconnect the brake line bracket and ABS sensor
    • Remove the upper stabilizer bolt with an 18mm wrench and a 10 mm wrench to secure it.
    • Remove the lower stabilizer bolt using your 18 mm wrench to secure it and a 21 mm socket.
    • Use a hammer to drive the bolt all the way out.
    • Move the steering knuckle off the strut with a hammer.
    • Tap the axle with a hammer and use a pry bar to pry it out of the steering knuckle.
    • Pry the other end of the axle out.
  4. step : Remove Brake Caliper (6:00)
    • Use your 12mm and 15mm socket wrenches to remove the calipers and caliper brackets.
    • Use a wire tie to help prevent stress on the caliper.
    • Use your socket to remove the brackets.
    • Use a wire tie to secure the caliper up out of the way.
  5. step : Remove the brake rotor (7:00)
    • Take care not to touch the rotor, and if you do make sure to clean it with rubbing alcohol or mineral spirits.
  6. step : Remove Hub (7:08)
    • On this vehicle, the hub is cast iron and the knuckle is aluminum, seizing is a potential issue.
    • Use an air hammer and protective eyewear to break the hub free if this happens.
    • Remove the hub with a hammer.
    • Clean up any corrosion with a wire brush.
  7. step : Install new hub (9:26)
    • Use some penetrating oil or anti-seize grease to prep the knuckle for the new hub.
    • Put the three 15 mm bolts in place and tighten the nuts to 70 ft lbs.
    • Check out our other videos to see how to finish putting everything back together.

Tools needed for replacement:

    General Tools

  • Floor Jack
  • Large Hammer
  • Jack Stands
  • Wire Brush
  • Hammer

  • Materials, Fluids, and Supplies

  • Anti-Seize Grease
  • Rust Penetrant
  • Wire Ties

  • Ratchets & Related

  • Socket Extensions
  • Ratchet

  • Sockets - Metric

  • 15mm Socket
  • 11mm Socket
  • 18mm Socket
  • 14mm Socket
  • 21mm Socket
  • 10mm Socket
  • 12mm Socket
  • 17mm Socket
  • 20mm Socket
  • 19mm Socket
  • 13mm Socket
  • 16mm Socket

  • Specialty Tools

  • Tie Rod Puller

  • Wrenches - Metric

  • 18mm Wrench
  • 10mm Wrench
  • 13mm Wrench
  • 17mm Wrench
  • 12mm Wrench
  • 15mm Wrench
  • 14mm Wrench
  • 11mm Wrench
  • 16mm Wrench

There are no reviews for this item. Write Review
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

  • 1996-2007 Ford Taurus 4 Piece Set Steering Kit
  • 1996-2005 Mercury Sable 4 Piece Set Steering Kit

This part replaces:

  • Moog ES3349RL
  • Dorman 951-037
  • Hollander 538-01667, 538-01365B, A
  • OE # 3F1Z 1104 BA
  • Reference Number 513100
Part #: 1AHTF00008



How-to Video:

(09:55 min)