Replaces

Ford Taurus Mercury Sable Steering & Suspension Kit - 1ASFK02890

Specifications:

  • Brand New Steering & Suspension Kit
  • Comes as a 16 Piece Kit
    • Fits LH (Driver Side) & RH (Passenger Side) Front & Rear
  • Direct replacement
  • Built to strict quality control standards

Our steering and suspension components come pre-greased, sealed for long life, and do not require the extra maintenance typically required by greasable versions.

Direct Fit

Application-specific, with no modifications required.

Rigorously Tested

Made from higher quality materials than the competition. Built to have a longer life in any environment or road conditions.

State of the Art Manufacturing

By the same factories that the OEMs use.

Prepackaged for Your Convenience

Carefully assembled to include all of the parts you need, saving time and money.

Part Details

  • Kit Includes: (2) Front Lower Ball Joints
  • Kit Includes: (2) Front Outer Tie Rods
  • Quantity: 16 Piece Set
  • Kit Includes: (2) Front Sway Bar Links
  • Kit Includes: (2) Rear Sway Bar Links
  • Kit Includes: (2) Steering Rack & Pinion Bellows
  • Kit Includes: (2) Rear Shock & Spring Assemblies
  • Kit Includes: (2) Front Strut & Spring Assemblies
  • Kit Includes: (2) Front Inner Tie Rods

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

Please Note: Whenever replacing steering components, it is highly recommended to have a professional alignment performed on the vehicle afterwards.  Failure to do so may result in issues with steering and premature tire wear.

  1. step : Remove Wheel (2:25)
    • Remove lug nuts and remove wheel.
  2. step : Remove tie rod (2:37)
    • Remove cotter pin.
    • Use your tie rod puller to pull the tie rod up.
    • Use your two adjustable wrenches to remove the tie rod.
  3. step : Install new tie rod (5:30)
    • Use the old nut to mark the bolt with tape.
    • Use a vice grip and an adjustable wrench to remove the nut, using penetrating oil if need be.
    • Replace bolt with new one, compensating for any difference in width.
    • Use your two adjustable wrenches to tighten the nut up against the tie rod end.
    • Use your torque wrench to tighten up the nut on the end of the tie rod and put the cotter pin in.
    • Put the grease fitting in.
    • Use grease gun to fill boot with grease.
  4. step : Put wheel back on (9:48)
    • Use the star pattern to tighten the lugs to 90 to 100 ft lbs.

Tools needed for replacement:

    Pliers, Cutters & misc Wrenches

  • Needle nose pliers
  • Adjustable Wrench

  • Ratchets & Related

  • Ratchet

  • Sockets - Metric

  • 18mm Socket
  • 19mm Socket

  • Specialty Tools

  • Grease Gun
  • Tie Rod Puller
  • Vise-Grips

  • Wrenches - Metric

  • 8mm Wrench

There are no reviews for this item. Write Review
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

  • 1996-1999 Ford Taurus Sedan 16 Piece Set Steering & Suspension Kit (excluding SHO Models) without Electronic Suspension
  • 2000-2007 Ford Taurus Sedan 16 Piece Set Steering & Suspension Kit
  • 1996-2005 Mercury Sable Sedan 16 Piece Set Steering & Suspension Kit

This part replaces:

  • Hollander 527-01225
  • Moog K8465
  • OE # E69Z3332A,E7FZ3332A
  • Monroe 181616
  • Monroe 181615
  • Monroe 171616
  • Monroe 171615
  • KYB SR4011
  • KYB SR4010
  • Moog K3124
  • Moog K8687
  • Moog K8734
  • Moog K8735
  • Moog ES3349RL
  • Moog EV398
Part #: 1ASFK02890

How-to Video:

(10:21 min)