Replaces

Ford Taurus Mercury Sable Steering & Suspension Kit - 1AHTF00032

Description
Warranty & Shipping
How-To & Tools
Product Reviews
Q&A
Vehicle Fit

Part Details

  • Bearing Type:   Ball Bearing
  • Quantity:   8 Piece Set
  • Kit Includes:
      (2) Front Lower Ball Joints
      (2) Front Sway Bar Links
      (2) Front Hub Assemblies
      (2) Front Strut & Spring Assemblies

Specifications:

  • Brand New 8 Piece Steering & Suspension Kit
  • Fits both LH (Driver Side) & RH (Passenger Side) Front
  • Direct replacements
  • Built to strict quality control standards

Our steering and suspension components come pre-greased, sealed for long life, and do not require the extra maintenance typically required by greasable versions.

Direct Fit

Application-specific, with no modifications required.

Rigorously Tested

Made from higher quality materials than the competition. Built to have a longer life in any environment or road conditions.

State of the Art Manufacturing

By the same factories that the OEMs use.

Prepackaged for Your Convenience

Carefully assembled to include all of the parts you need, saving time and money.

Item Condition: New

California Customers:

WARNING:  This product can expose you to chemicals including Chromium (Hexavalent Compounds), which is known to the State of California to cause cancer, and birth defects or other reproductive harm.  For more information, go to www.P65Warnings.ca.gov.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

  1. step : Remove Wheel (1:09)
    • Remove hub nut
    • Remove lug nuts and remove wheel with an 18mm socket.
  2. step : Remove tie rod (1:50)
    • Remove cotter pin.
    • Use your 18 mm socket to remove the nut at the bottom of the tie rod.
    • Use your tie rod puller to pull the tie rod up.
    • Use your two adjustable wrenches to remove the tie rod.
  3. step : Remove the axle. (2:42)
    • Disconnect the brake line bracket and ABS sensor
    • Remove the upper stabilizer bolt with an 18mm wrench and a 10 mm wrench to secure it.
    • Remove the lower stabilizer bolt using your 18 mm wrench to secure it and a 21 mm socket.
    • Use a hammer to drive the bolt all the way out.
    • Move the steering knuckle off the strut with a hammer.
    • Tap the axle with a hammer and use a pry bar to pry it out of the steering knuckle.
    • Pry the other end of the axle out.
  4. step : Remove Brake Caliper (6:00)
    • Use your 12mm and 15mm socket wrenches to remove the calipers and caliper brackets.
    • Use a wire tie to help prevent stress on the caliper.
    • Use your socket to remove the brackets.
    • Use a wire tie to secure the caliper up out of the way.
  5. step : Remove the brake rotor (7:00)
    • Take care not to touch the rotor, and if you do make sure to clean it with rubbing alcohol or mineral spirits.
  6. step : Remove Hub (7:08)
    • On this vehicle, the hub is cast iron and the knuckle is aluminum, seizing is a potential issue.
    • Use an air hammer and protective eyewear to break the hub free if this happens.
    • Remove the hub with a hammer.
    • Clean up any corrosion with a wire brush.
  7. step : Install new hub (9:26)
    • Use some penetrating oil or anti-seize grease to prep the knuckle for the new hub.
    • Put the three 15 mm bolts in place and tighten the nuts to 70 ft lbs.
    • Check out our other videos to see how to finish putting everything back together.

Tools needed for replacement:

    General Tools

  • Floor Jack
  • Large Hammer
  • Jack Stands
  • Wire Brush
  • Hammer

  • Materials, Fluids, and Supplies

  • Anti-Seize Grease
  • Rust Penetrant
  • Wire Ties

  • Ratchets & Related

  • Socket Extensions
  • Ratchet

  • Sockets - Metric

  • 15mm Socket
  • 11mm Socket
  • 18mm Socket
  • 14mm Socket
  • 21mm Socket
  • 10mm Socket
  • 12mm Socket
  • 17mm Socket
  • 20mm Socket
  • 19mm Socket
  • 13mm Socket
  • 16mm Socket

  • Specialty Tools

  • Tie Rod Puller

  • Wrenches - Metric

  • 18mm Wrench
  • 10mm Wrench
  • 13mm Wrench
  • 17mm Wrench
  • 12mm Wrench
  • 15mm Wrench
  • 14mm Wrench
  • 11mm Wrench
  • 16mm Wrench

There are no reviews for this item.
Will this fit my car? Add a vehicle to make sure
Customer Q&A
Ask a question to 1A Auto customers who purchased the product
No questions have been asked about this item.
Year Make Model Description
1996-1999Ford Taurus Ford Taurus 8 Piece Set Front Steering & Suspension Kit without Electronic Suspension (excluding SHO Models)
2000-2007Ford Taurus Ford Taurus 8 Piece Set Front Steering & Suspension Kit
1996-2005Mercury Sable Mercury Sable 8 Piece Set Front Steering & Suspension Kit
Part #: 1AHTF00032


Order must be placed by 4pm ET

Get it in: 2 - 4 Business Days

Want it sooner? Choose Next Day Air at Checkout

How-to Video:

(09:55 min)