Replaces
This part doesn’t fit a . Select from parts that fit.
1A Auto Lifetime Warranty
Frequently bought together
Complete Repair in One Purchase - Stop searching for parts individually and complete your repair with a customized kit or set from DIY Solutions.
High-Quality Parts from Trusted Brands - DIY Solutions' kits and sets are selected from the best automotive brands and include hard-to-find and even obsolete parts you may need for your vehicle.
Guaranteed Fit - DIY Solutions ensures its selected parts are quality-tested to guarantee fit and function.
Assemblies may include halogen or incandescent test bulbs that should be replaced before installation.
Features and Benefits
Item Condition:
New
Attention California Customers:
WARNING: This product can expose you to chemicals including Chromium (Hexavalent Compounds), which is known to the State of California to cause cancer, and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov
Lifetime Warranty
This item is backed by our limited lifetime warranty. In the event that this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.
Created on:
Tools used
Brought to you by 1AAuto.com- your source for quality replacement parts and the best service on the internet.
Hi I'm Mike Green. I'm one of the owners of 1A Auto. I want to help you save time and money repairing or maintaining your vehicle. I'm going to use my twenty plus years experience restoring and repairing cars and trucks like this to show you the correct way to install parts from 1AAuto.com. The right part, installed correctly, that's going to save you time and money. Thank you and enjoy the video.
In this video we're going to show you how to replace your headlight and signal bulbs as well as your whole signal light assembly on this 2001 Ford Taurus. Same as any 2000 to 2007. You'll need an eight millimeter socket and ratchet.
Okay you start by loosening up an eight millimeter bolt right here and you just have to loosen it up a little bit, do not take the bolt all the way out. Then there's two clips that hold it in, one's easy to see right here. You basically use a screwdriver and pry up the on the clip and pull it out. Then we'll do a close up on the other one back here, there it is. Same thing, pull it up and out. Then your headlight just basically pulls out. Now, this car has a little bit of damage to the front end so it actually comes out a little difficult. Usually you pull the inside near the grill out first and then the outside. Now there's a connector, just use the little thumb tab to push down on it. Then you disconnect the whole assembly. If you're looking to change your headlight bulb you untwist that right there. Then your headlight bulb is inside. There's a retaining ring that you need to twist counter clock wise and then the bulb comes out and you can disconnect the bulb from the harness and you can replace it. I'm going to put this back together, just kind of put it back and we're actually going to swap the harness over to a new light. So I'll put that back in there for right now. Now you're signal bulb just twists to come out and the bulb just twists to come out of the socket and goes back in. Then note it should be an orange bulb.
Okay so we're going to replace this headlight with a new one and with the couple little retainers that hold the harness onto the light you just pry them up. So here's the new light from 1A down on the bottom. This old light looks like some kind of aftermarket; it has some black painting on it which looks terrible on this car. You can see the new light, nice and shiny. I'm going to pull, it comes with a protective kind of saran wrap on it, and I'm going to pull the edges of that off a little bit. I'm not going to pull all of that off until it's installed that way you keep your finger prints off it. Now I'm just going to take the retaining ring off, these little protective covers just keep stuff out of the light during shipping. The headlight bulb does go in a certain way. There are three apiece on the headlight and then slots on the bulb itself. You just need to make sure you line it up. Two of them are closer to each other and then one is further away. Then you push that down in and now I'm just kind of wrestling with the retainer ring a little bit trying to get it on there nice and tight. You turn it clockwise. Then with the signal bulb you put it on there and turn it clockwise, tighten it and put the harness onto its little pins. Then the big thing there that protects the harness bulb- put that in there and turn it clockwise. Then put that down into place and connect your harness again. That's an extra retainer ring that I think came, or that's the old one from the other bulb.
Okay and then you want to put the headlight in, you want to put it into the fender side first and then push it on the inside and again this car had some damage on it so it's a little more difficult than it should be. I'm kind of giving it a little bit of strength there. You push it into the fender and then you can push it underneath that bolt that you loosened. Now you can see I'm going to tighten up that bolt. Kind of do it half way, then I put the retaining tabs back in. Easy enough just push in on the light if you have and slide them back in. Now I'll tighten that eight millimeter bolt and then I'll pull the protective plastic off of that light and then we have a nice new light on the car. It looks a lot better than the old one.
We hope this helps you out. Brought to you by www.1AAuto.com your source for quality replacement parts and service on the internet. Please feel free to call us at 888-844-3393 we're the company that's here for you on the internet and in person.
