Replaces
This part doesn’t fit a . Select from parts that fit.
Light Assembly Lifetime Warranty
Frequently bought together
Assemblies may include halogen or incandescent test bulbs that should be replaced before installation.
Features and Benefits
Item Condition:
New
Attention California Customers:
WARNING: This product can expose you to chemicals including Lead and Lead Compounds, which are known to the State of California to cause cancer, and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov.
This item is backed by our limited lifetime warranty. In the event this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.
The bulbs are for testing and not covered under our warranty. Our warranty applies to the light assembly only.
FREE Shipping is standard on Orders shipped to the lower 48 States (Contiguous United States). Standard shipping charges apply to Hawaii, Alaska and US Territories. Shipping is not available to Canada.
Expedited is available on checkout to the United States, excluding Alaska, Hawaii and US Territories as well as P.O. Boxes and APO/FPO/DPO addresses. Final shipping costs are available at checkout.
Created on:
Tools used
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.
Hi, I'm Mike Green. I'm one of the owners of 1A Auto. I want to help you save time and money repairing or maintaining your vehicle. I'm going to use my 20-plus years experience restoring and repairing cars and trucks like this to show you the correct way to install parts from 1AAuto.com. The right parts installed correctly: that's going to save you time and money. Thank you and enjoy the video.
In this video, we're going to show you how to replace the side marker on this 1997 Expedition, same as any '97 to '02 Expedition and also '97 to '03 F150. The only tool you'll need is a T20 Torx driver or actually a 8 millimeter or 9 millimeter socket and ratchet would work too. To replace either the light bulb or to replace the side marker light, you'll need a T20 Torx driver and you remove this bolt right here. Once that bolt is removed then you can just pull it out and then disconnect your harness and you could service the bulb just by twisting and taking it out.
So here's our original. Here is the one then the one from 1A Auto, they're all the same. We can remove the bulb there and put it in to one in the 1A Auto light. So, maybe, you just want to freshen up your lights, put on the nicer, clearer ones, or maybe you got on a little accident and this one is broken. The 1A Auto one is going in nice and easy for you. Connect the harness. You have a groove here, and there's a slot, here that goes into and then a slot here and a groove here that it goes into, so feed the wire back in, make sure your lower part is in that and the slot's in the groove and then feed it back in. Now your pins have to go back and into the fender. Now, you take your T20 screw again and put it in and you're all set.
We hope this video helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.
Tools used
Hi, I'm Mike from 1AAuto. We've been selling auto parts for over 30 years! We're dedicated to delivering quality auto parts, expert customer service, and fast and free shipping, all backed by our 100% satisfaction guarantee. So visit us at 1AAuto.com, your trusted source for quality auto parts.
In this video we are going to be working with our 1998 Ford F-150.
We're going to show you how to remove and replace your vehicles turn signal assembly on the front of the truck. If you like this video, please click subscribe. We have a ton more information on this and many other vehicles. If you need parts for your truck, you can follow the link down in the description over to 1AAuto.com.
Here are the items that you will need for this repair: 7mm-15mm socket, ratchet, socket extension, interior trim removal tool kit from 1AAuto.com, flat head screwdriver, Phillips screwdriver
To remove your headlight, lift up on the two tabs behind it. Sometimes you got to wiggle them a little to get them to stay in place and work your headlight out. You may be able to reach in from the back and push on it. You got to make sure these tabs are fully disengaged. Over time, they wear out and they tend to get a little stuck. Once that's out, you can unclick your headlight harness and remove it.
On the inside edge of the fender is a 7mm screw you'll want to remove that with a seven millimeter socket ratchet and extension. Once that's out, you can slide the turn signal assembly out of the grille, undo the tabs, and remove it from the vehicle.
So here we have our old aftermarket parking lights that we removed from our truck, and our new parts from 1AAuto.com. As you can see there are some clear aesthetic differences here, our old lights that we removed have a smoked lens and a black housing where our new parts have the original clear lens and chrome housing. These are gonna have a much nicer light output than these parts here are.
Also, looking at the quality, inside of this lens the reflective material is actually chipping away and failing. On top of that it is a black chrome when isn't going to reflect light as well, hurting the light output. We also have the smoked lens, which is going to reduce that light output even more. So to make sure that your signals are nice and bright and clear so people can see you and know what you're doing, these new parts from 1A Auto will go into direct fit just like your original equipment and fix you up right.
Plug in your headlight bulb and line up the pins with their slots, so the tabs here will sit in between these two slots and go through that hole. And you can see the lock plate and how that works there. So you will have to kind of hold this up if your spring’s weak and it doesn't keep itself up there. You want to line up the rear ones at the same time.
Now you've got your new headlight in place. For your marker light, we’ll just plug that in, line it up, and slide it into place. When it's all the way set in, your hole will be lined up at the top. We'll reinstall that seven millimeter screw. So on the driver’s side of our truck, we have the old smoked housing headlights that we're removing from our truck and replacing with our new parts from 1A Auto.
I think the difference is pretty clear here. Much brighter, much easier to see on this side, this side is very dim, it's difficult to see. You're not getting the great light output either from the blinker or marker, or the headlight. Neither of those are really shining through as well as our new parts from 1A Auto are. These are facing straight ahead, right at level where they should be, and part of that is due to adjustment, whereas this one is actually shining on the wall over to my left, which is not what you want on the road obviously, you want to see in front of you. That's going to be shining off into the other lane, annoying other drivers and not putting light on the road where you want it. Close your hood, and you're good to go.
Thanks for watching. Visit us at 1AAuto.com for quality auto parts, fast and free shipping, and the best customer service in the industry.
