Replaces

Ford Mazda Steering & Suspension Kit 8 Piece Set TRQ PSA58839 - 1ASFK02186

Frequently bought together

Description
Warranty & Shipping
How-To & Tools
Product Reviews
Q&A
Vehicle Fit

Part Details

  • Quantity:   8 Piece Set
  • Kit Includes:
      (2) Front Lower Ball Joints
      (2) Front Upper Control Arms with Ball Joints
      (2) Front Outer Tie Rods
      (2) Front Inner Tie Rods

These replacement control arms/ball joints are just what you need to ensure the safety and integrity of your vehicle's suspension and steering.

Specifications:

  • 8 Piece Steering & Suspension Kit includes:
    • (2) - FRONT UPPER Control Arms - LH (Driver Side) & RH (Passenger Side)
    • (2) - FRONT LOWER Ball Joints - LH (Driver Side) & RH (Passenger Side)
    • (2) - FRONT INNER Tie Rod Ends - LH (Driver Side) & RH (Passenger Side)
    • (2) - FRONT OUTER Tie Rod Ends - LH (Driver Side) & RH (Passenger Side)
  • Direct replacements
  • Built to strict quality control standards
  • Fit 2WD (Two Wheel Drive) Models only
  • Correct for models with Front Coil Spring Suspension
    • Do NOT fit models with Torsion Bar Suspension

Worn ball joints can cause excessive front tire wear, popping or creaking in the front end, extra play in the steering system, and pose a serious safety concern. Replace loose or worn ball joints with our quality replacements.

One way to diagnose a loose, or warn ball joint, is to jack the car up, so the wheel is off of the ground, then have someone try to move the wheel in and out. While they are moving the wheel check the ball joint for play, if it is moving you probably need to replace it.

Remember whenever you are replacing any front end or steering components you should have your vehicle professionally aligned as soon as possible. This will ensure proper tracking and even tire wear.

Our steering and suspension components come pre-greased, sealed for long life, and do not require the extra maintenance typically required by greasable versions.

Direct Fit

Application-specific, with no modifications required.

Rigorously Tested

Made from higher quality materials than the competition. Built to have a longer life in any environment or road conditions.

State of the Art Manufacturing

By the same factories that the OEMs use.

Prepackaged for Your Convenience

Carefully assembled to include all of the parts you need, saving time and money.

Item Condition: New

Attention California Customers:

WARNING:  This product can expose you to chemicals including Chromium (Hexavalent Compounds), which is known to the State of California to cause cancer, and birth defects or other reproductive harm.  For more information, go to www.P65Warnings.ca.gov.

Lifetime Warranty

This item is backed by our limited lifetime warranty. In the event this item should fail due to manufacturing defects during intended use, we will replace the part free of charge.

Note: When replacing steering components, it is recommended to have a professional alignment performed on the vehicle afterwards. This will ensure proper tracking and even tire wear.

  1. step : Remove the wheel (1:10)
    • Loosen the lug nuts
    • Raise and secure the vehicle
    • Remove the lug nuts and set the wheel aside.
    • Put the wheel under the vehicle for added security in the event of a jack failure.
  2. step : Remove the brakes (2:00)
    • Remove the 13 mm sockets anchoring the caliper.
    • Wire tie the caliper up out of the way.
    • Use a 15mm socket to remove the caliper bracket
    • Remove the rotor
    • Remove the dust shield with your 8 mm socket and ratchet
  3. step : Remove the outer tie rod (3:00)
    • Use your pliers to remove the cotter pin from the tie rod
    • Remove the nut with your 21 mm socket and ratchet
    • Pull apart the tie rod with a tie rod puller.
    • Use a paint marker to mark where the top nut on the tie rod is.
    • Use two adjustable wrenches to remove the tie rod.
  4. step : Install the new tie rod (6:15)
    • Apply a little loctite to the inner tie rod
    • Screw on the outer tie rod to the inner tie rod up to your paint marker mark.
    • Fill the dust boot with grease
    • Reassemble the tie rod end, replacing the nut and cotter pin.
    • Reassemble the brakes and wheel.
    • See our other videos for more detailed instructions.

Tools needed for replacement:

    General Tools

  • Jack Stands
  • Floor Jack

  • Materials, Fluids, and Supplies

  • Wire Ties
  • Liquid Thread Locker
  • Marker / Writing Utensil
  • Rust Penetrant

  • Pliers, Cutters & misc Wrenches

  • Needle nose pliers
  • Lug Wrench
  • Wire Cutters

  • Ratchets & Related

  • Ratchet
  • 1/2 Inch Breaker Bar

  • Screwdrivers & Related

  • Flat Blade Screwdriver

  • Sockets - Metric

  • 13mm Socket
  • 8mm Socket
  • 15mm Socket
  • 21mm Socket

  • Specialty Tools

  • Tie Rod Puller

3.00/ 5.0
1review
5 Stars
4 Stars
3 Stars
2 Stars
1 Star
0
0
1
0
0
Upper and lower ball joints
I was not able to putting the rubber seal on to protect the lower ball joint. Ended forcing the rubber cup as far as I could. The top ball joint had wire holding the rubber cup on. Should have some type of tool to put in place.!
February 27, 2017
Will this fit my car? Add a vehicle to make sure
Customer Q&A
Ask a question to 1A Auto customers who purchased the product
No questions have been asked about this item.
Year Make Model Description
1998-2000Ford Ranger Ford Ranger Rear Wheel Drive Steering & Suspension Kit 8 Piece Set
2001-2005Ford Ranger Ford Ranger (excluding Edge Models) Rear Wheel Drive Steering & Suspension Kit 8 Piece Set
2006-2009Ford Ranger Ford Ranger (excluding Sport Model) Rear Wheel Drive Steering & Suspension Kit 8 Piece Set
2010-2011Ford Ranger Ford Ranger Rear Wheel Drive Steering & Suspension Kit 8 Piece Set
2001-2009Mazda B2300 Truck Mazda B2300 Truck Steering & Suspension Kit 8 Piece Set
1998-2001Mazda B2500 Truck Mazda B2500 Truck Rear Wheel Drive with Front Coil Spring Suspension Steering & Suspension Kit 8 Piece Set
1998Mazda B3000 Truck Mazda B3000 Truck Rear Wheel Drive with Front Coil Spring Suspension Steering & Suspension Kit 8 Piece Set
1999-2000Mazda B3000 Truck Mazda B3000 Truck (excluding Troy Lee Models) Rear Wheel Drive Steering & Suspension Kit 8 Piece Set
2001-2007Mazda B3000 Truck Mazda B3000 Truck (excluding Dual Sport Models) Rear Wheel Drive Steering & Suspension Kit 8 Piece Set
1998Mazda B4000 Truck Mazda B4000 Truck Rear Wheel Drive with Front Coil Spring Suspension Steering & Suspension Kit 8 Piece Set
1999-2000Mazda B4000 Truck Mazda B4000 Truck (excluding Troy Lee Models) Rear Wheel Drive Steering & Suspension Kit 8 Piece Set
2001-2003Mazda B4000 Truck Mazda B4000 Truck (excluding Dual Sport Models) Rear Wheel Drive Steering & Suspension Kit 8 Piece Set
Part 1ASFK02186
In Stock


Order must be placed by 4pm ET
Delivery options for:

Estimated Arrival Cost


Deliveries made to PO Boxes and FPO may take longer. See our Shipping & Delivery for more information.

TRQ
Brand #: PSA58839