Ford Mazda Lincoln Mercury 4 Piece O2 Oxygen Sensor Set TRQ OSA61636

All right, friends, it's gonna be time to get started on our downstream O2 sensor. First, you want to make sure that you have the correct O2 sensor. The downstream is gonna be the one that's located on the rearward aspect of the catalytic converter, and it's gonna have the shorter wire. The upstream O2 sensor is gonna be located on the same pipe, but it's gonna have a much longer wire and a different connector. I'm just going to use our O2 sensor socket here, we'll get it on there and break this free.

The next thing we would wanna do is follow that wire to the connector. There's gonna be a little push tab that you're going to push on, and then you're going to separate the two pieces. There we are. Go ahead and grab that wiring, bring it down to the O2 sensor and then remove your O2 sensor. There it is, friends. Now it's gonna be time to install our brand new O2 sensor. I'm just gonna take the wire go over the driveshaft. We'll go ahead and start this in, bottom it out and then we'll torque it to 46 foo-pounds. Just use a tiny bit of dielectric grease inside the electrical connector, and let's get it connected in, give it a nice click and a nice tug, make sure it's completely secured. And, of course, if it came off the bracket, just make sure you re-secure it with something. Lastly, let's go ahead and put this back inside there, and you should be good to go.

Hi, I'm Mike from 1A Auto. We've been selling auto parts for over 30 years. We're dedicated to delivering quality auto parts, expert customer service, fast and free shipping, all backed by our 100% satisfaction guarantee. Visit us at 1AAuto.com, your trusted source for quality auto parts.

Right here on the passenger side of the tuck, on the rear, right behind the catalytic converter, is your rear O2 sensor. It's also known as a downstream O2 sensor, and it's quite easy to take out on this truck. This one actually has a newer exhaust system in it, which is actually making it even easier for us. If yours is old and rusty, it'll take a little bit more force, but it'll still work the same exact way. We're going to start with a 22 millimeter wrench on the O2 sensor itself. We should be able to loosen it up just like that. There is such a thing as an O2 sensor socket, which also makes life a little bit easier. There you go, it's actually out of the pipe that easily.

An O2 sensor socket will make it easier because it fits around the whole socket, or the whole O2 sensor itself, and it allows the wires to go through. So you can use a big breaker bar if you need to instead of a wrench that might slip.

Up at the top of the sensor is a connector, which you need to disconnect to get the sensor out of the truck. Looks like it's going to be a two handed thing. I apologize for kind of blocking the camera there, but you can see this is how the clip works. You push down the tab right here and it releases it from the other connector. Whenever you install an O2 sensor, you never want to plug it in first. You always want to install it first, because when you install it. It's going to spin and if the connector doesn't spin, you're going to bind up all the wires and sometimes it'll actually damage the wire. If you're ever putting an O2 sensor in, make sure you screw it in first. Then once it's all the way screwed in, then you plug it in.

Same 22 millimeter wrench is what we're going to use to tighten it. At that point, you can go up to where you disconnected it. It's the blue connector right on top of the transfer case. Where the transfer case meets the transmission, I should say. At this point, it should snap right into place. Just like that. You'll feel it click.

Thanks for watching. Visit us at 1AAuto.com for quality auto parts, fast and free shipping, and the best customer service in the industry.

Hi, I'm Mike from 1A Auto. We've been selling auto parts for over 30 years. We're dedicated to delivering quality auto parts, expert customer service, fast and free shipping, all backed by our 100% satisfaction guarantee. Visit us at 1AAuto.com, your trusted source for quality auto parts.

In this video, we're going to show you how to replace the downstream oxygen sensor on this 2006 Ford Explorer. It has the 4.6 liter engine. We show you on, I believe the passenger side; driver's side's the same procedure. We hope you like the video. Please click subscribe. Check out 1AAuto.com for all your parts needs for your Explorer or whatever vehicle you might have. Here are the items you'll need for this repair.

Raise and support your vehicle with jack and jack stands. We have ours on a lift. The downstream oxygen sensors are the ones that go right into the catalytic converter. Passenger side is here and driver's side is over here. We're going to show you how to replace the passenger side one.

Follow your oxygen sensor connection up to this blue connector here. There's a tab right here. Press with your thumb and pull to disconnect. To remove your bad O2 sensor, just use a pair of pliers or a pair of wire cutters and cut the wires. That allows you to easily get a 7/8ths wrench right down and on. Many times these are in there kind of tough, so I like to use a hammer just to give it some impact. A few hits will loosen it up. Use some rust penetrant and let it sit. And then I've got it out a little bit and then put rust oil on there, rust penetrant, and now I'm actually going to thread it back in and see if I can work some down in. The old sensor is out.

Here are the old sensor from the vehicle and the new one from 1A Auto. Remove the shipping protector before installation. The connections are exactly the same. The oxygen sensors are exactly the same. The one from 1A Auto is going to be a very good replacement. It's going to fit and function just like your original. New oxygen sensors are available at 1AAuto.com.

Thread in the oxygen sensor. Use a 7/8ths wrench and use the open end to tighten it up. And then just make sure your lead goes up and the tab is down to go into the connector and plug it in and make sure it clicks.

Thanks for watching. Visit us at 1AAuto.com for quality auto parts, fast and free shipping, and the best customer service in the industry.

Hi, I'm Mike from 1A Auto. We've been selling auto parts for over 30 years. We're dedicated to delivering quality auto parts, expert customer service, fast and free shipping, all backed by our 100% satisfaction guarantee. Visit us at 1AAuto.com, your trusted source for quality auto parts.

In this video I have a couple of oxygen sensors with me. While there are some aesthetic differences here, the wire lengths are a little different, the actual body and tip of the sensor are a little different, the threads and gasket are the same, and on the other end the connections are actually the same. I can plug these into either position on our vehicle. But if I had to ask you which one's upstream and which one's downstream, you probably can't tell just from looking at them. That's true of most oxygen sensors. The way you determine whether or not an O2 sensor is upstream or downstream is all done visually.

Your oxygen sensor position can be determined relative to your catalytic convertor. As the name suggests, upstream sensors will be located upstream or ahead of, in front of, above, closer to the engine than your catalytic convertors. This means that they see the exhaust gasses first. They then go through the catalytic convertor and to the downstream oxygen sensor, which will either be located in the catalytic convertor like our vehicle here, or after the catalytic convertor to monitor the gasses coming out of the cat and make sure that it's being efficient relative to the readings of the upstream O2 sensor.

The other determination you need to make is bank one versus bank two. Determining which bank is which can be done by looking at a picture of your vehicle's firing order. Whichever bank contains cylinder one is going to be bank one, and the other one, regardless of whether or not cylinder two is in it, is going to be bank two by default. These banks are true of V engines like V8s, V6s, and flat engines like Porsches and Subarus that have individual banks.

On inline four-cylinder engines, as long as they have one exhaust manifold like a Jeep four-liter or a four-cylinder Honda engine, you'll only have one bank with an upstream and downstream O2 sensor. There will be no bank two on the engine.

On our vehicle here, this is the passenger side, which we've already determined from the firing order is bank one. We have our upstream sensor here closest to the engine ahead of the cat. Then we have our downstream or sensor two here inside of the catalytic convertor. This could also be located somewhere after the cat. Here I have my two sensors for the vehicle. While they are aesthetically different, we can now tell this is my upstream sensor because it looks just like the upstream sensor I have up there. This is my downstream sensor. Now that we know which one's which, we can order the right part, correct the problem, and fix you up right.

Thanks for watching. Visit us at 1AAuto.com for quality auto parts, fast and free shipping, and the best customer service in the industry.

Okay, friends. It's time to get started on our downstream O2 sensor. You're gonna find that located on your vehicle's exhaust. On this particular vehicle, it's right inside the catalytic converter. I'm gonna be doing the one on the driver's side, but the passenger's side would be approximately the same. One of the first things I like to do is disconnect the wiring. You can take a small pocket screwdriver or even just your finger, push on this tab, and then separate the two pieces.

I always like to take a peek at my connectors on both sides just to make sure I don't see any funny colors. I know I'm replacing the O2 sensor, but if I see some corrosion on this side, more than likely, there's some on the other side. At this point, I'm gonna remove the O2 sensor from the catalytic converter. You're gonna need a special tool for that, and it looks like this right here. You can see that it has a slot, and it's gonna fit right over the wire for your O2 sensor. Fits right on the O2 sensor, and try to break it free. There we are. Okay. There's our O2 sensor, friends.

Okay, friends. Now, it's gonna be time to get our brand new downstream O2 sensor in here. You're gonna notice on the threads that you have a little bit of Never-Seez. Leave it on there, but be careful not to get in on the sensing agent. We're gonna start this in by hand, and then, once it bottoms out by hand, we'll go ahead and snug it up with our tool. So now, we're just gonna go ahead and snug this up. I have it so it's bottomed out. We're just gonna go a teeny bit more because we wanna make sure that we crush down that gasket. That's nice and tight right there.

Next, of course, you wanna connect in the O2 sensor to the harness. Push that right in. Make sure it's locked. Give it a nice tug. If you have any excess cable, make sure that you just, kinda, tie this up so it's gonna be nice and secure. I'm gonna use a wire tie. Okay, friends. So, you finished your O2 sensor. Great job. Now, what you need to do is if you had a check engine light on, clear that code. Take your vehicle for a road test. If your check engine light stays off, you did great.