Replaces
Frequently bought together
Left Hand Drive:
All of our auto parts are intended for Left Hand Drive USDM vehicles. If your vehicle is Right Hand Drive, please ensure the part is correct for your specific vehicle.
Highest Quality MaterialsMade from highest quality materials that meet or exceed OEM standards
Quality Tested - built to a strict level of product standards.
Item Condition:
New
Attention California Customers:
WARNING: This product can expose you to chemicals including Lead and Lead Compounds, which are known to the State of California to cause cancer, and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov.
Lifetime Warranty
This item is backed by our limited lifetime warranty. In the event that this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.
Returns: Parts with electrical components cannot be returned once installed.
FREE Shipping is standard on Orders shipped to the lower 48 States (Contiguous United States). Standard shipping charges apply to Hawaii, Alaska and US Territories. Shipping is not available to Canada.
Expedited is available on checkout to the United States, excluding Alaska, Hawaii and US Territories as well as P.O. Boxes and APO/FPO/DPO addresses. Final shipping costs are available at checkout.
Created on:
Tools used
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.
Hi, I'm Mike from 1A Auto. I hope this how-to video helps you out, and next time you need parts for your vehicle, think of 1AAuto.com. Thanks.
In this video, we're going to show you how to replace the blower motor on this 2005 Ford F150. It's the same part and similar process on these F150s from 2004 to 2008. The items you'll need for this is a new blower motor from 1AAuto.com and an 8 millimeter socket and ratchet.
Your blower motor is located right here. It's held in with these three 8 millimeter bolts. Then disconnect the harness by pulling down on the tab and pushing it off. Then use an 8 millimeter wrench or a socket and ratchet to remove those three 8 millimeter bolts. Once those are removed, just pull the blower motor down as far as you can and then pull back the carpeting, and just maneuver it down and out and over the carpeting.
On the left is the new blower motor from 1AAuto.com. On the right is the old one. You can see they're identical, and they'll fit exactly the same. Take your new blower motor and feed it up into place. You push it in against the carpet as much as you can. Once you get to a certain point, you'll want to pull the carpet back to give yourself a little bit extra room. Then just kind of push it into the insulation and up at the same time, and it'll go into place. Then turn it once you get it up in place so that the holes line up.
Once you get it lined up, just replace those bolts and tighten them up. If you want to speed up the process of tightening them up, you can use an air ratchet, but you want to make sure that you don't over-tighten them, so just tighten them most of the way, and then tighten them the rest of the way using your socket and ratchet. You just want them hand tight. Reconnect your harness.
We hope this video helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.
Tools used
All right, so coming in on your passenger's side, right underneath the glove box, you're gonna be able to see your blower motor resistor. It should be fairly easy to get to. We're gonna remove the wiring harness from it and then, of course, of the two mounting bolts. Let's get started.
Now, if you take your finger and you press right on this little center point, you'll be able to squeeze that and then draw this away. I always take a peek at my wiring harness. Make sure there's no funny colors. If you see something, you know you have to repair that. This looks good, so I'll set it aside. Now I can see my mounting bolt here and one right there, remove them both. There's one. It's out. There's our second. And then of course the blower motor resistor.
Now it's gonna be time to install our brand new blower motor resistor. If you were look at it, you can see that it has one corner that's, kind of, angled off. That needs to be on the top and towards the rear. I'm just gonna put it just like this, I'll slide it directly into the box, and then, of course, we'll put in our two mounting bolts. Okay. There it is. Just like that. Let's get this one in a few good threads. You want it to be as straight as possible. You're gonna be screwing into plastic, so it could be very simple to accidentally cross-thread in your bolt or even strip out the plastic box. Okay, so I get that one bottomed out. Do the same thing to the other one. You don't wanna overtighten these. Like I said, they're only screwed into plastic. Okay, that's bottomed out, just a tiny weeny bit more. That's it. Let's get our pigtail reattached. Push it in. Listen for a click. Give it a tug. That feels great. Now we're gonna test our blower motor.
All right, I can hear the blower motor on level one, two, three, oh yeah, and it works on high. This is perfect.
Tools used
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.
Hi, I'm Mike from 1A Auto. I hope this how-to video helps you out, and next time you need parts for your vehicle, think of 1AAuto.com. Thanks.
In this video, we're going to show you how to replace the blower motor resistor on this 2005 Ford F150. It's the same part and similar process on these F150s from 2004 to 2010. The items you'll need for this is new blower motor resistor from 1AAuto.com and an 8 millimeter socket and ratchet.
Open up your glove box and just push in on the passenger's side and pull it down. Now, push the tab on the bottom of this harness and then just pull it free. Then remove these two 8 millimeter bolts. We'll fast forward as Mike does that. You can use an air ratchet for this, just to speed up the process. Once you remove the bolts, it pulls right out. Then, you just want to pull off this gasket as well.
On the left is the old blower motor resistor. On the right is the new one from 1AAuto. You can see they're identical and they'll fit exactly the same. Make sure the gasket's in place, and then feed your blower motor resistor back into place. Then, replace those two 8 millimeter bolts by hand. One corner is notched and there's a tab in it, so you can only put it in one way. Tighten up the bolts, careful not to over-tighten them. You don't want to strip out the plastic. Reconnect your harness and then push in the side of your glove box and close it.
We hope this video helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.
