Replaces

Ford Focus Shock Absorber Pair TRQ SBA60342 - 1ASSP00799

Description
Warranty & Shipping
How-To & Tools
Product Reviews
Q&A
Vehicle Fit

Part Details

  • Quantity:   Pair

Our direct fit gas-charged shock absorbers help to restore your vehicle’s handling and ride quality to just like new.

Direct Fit

Fits and functions correctly.  Competitors combine applications to reduce the amount of parts they carry, resulting in: incorrect vehicle height, poor response and an uncomfortable ride.

Rigorously Tested

Made from higher quality materials than the competition. Built to have a longer life in any environment or road conditions.

Matched Parts

Not all shocks and struts are manufactured the same.  Mixing and matching can result in ride quality issues and decrease the life of the parts.

Saves Time & Money

Over buying the parts individually, or having to search different parts that are correct for your vehicle (because we did it for you!)

Item Condition: New

California Customers:

WARNING:  This product can expose you to chemicals including Chromium (Hexavalent Compounds), which is known to the State of California to cause cancer, and birth defects or other reproductive harm.  For more information, go to www.P65Warnings.ca.gov.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

  1. step : Accessing the Shocks and Struts (1:03)
    • Loosen the lug nuts on the wheel while the car is on the ground
    • Jack the car up and remove the lug nuts and wheel
    • Pull the brake line from the bracket
    • Pull the ABS sensor out of its bracket
    • Remove the bolt on the upper stabilizer link. Spray with penetrating oil
    • Spray the bolt on the back side of the strut with penetrating oil
    • Use a socket to remove the 15mm bolt on the steering knuckle
  2. step : Removing the Strut (4:27)
    • Spray penetrating oil where the strut connect with the steering knuckle
    • Use a 15mm socket to disconnect the tie rod. Use a jack and some wood to hold the tie rod up to help remove the bolt
    • If the vehicle has a broken spring lift up on the strut and hammer the steering knuckle until it loosens
    • Lift the strut up and out of the steering knuckle
    • Remove the three 13mm bolts up in the engine compartment
    • Pull the strut free
  3. step : Installing a New Strut (6:40)
    • With the clip on the bottom of the strut facing inward, put the strut into place
    • Replace the bolts in the engine compartment
    • Pull the steering knuckle out and slide it on to the bottom of the strut
    • Replace the bolt that connects the strut to the steering knuckle. Do not tighten fully
    • Make sure the steering knuckle is below the taper on the strut
    • Make sure its at the right depth and moves properly
    • Tighten the bolt on the steering knuckle to between 65 and 70ft/lbs
  4. step : Reconnecting the Brackets and Sensors (9:52)
    • Put the brake line back in place
    • Put the tie rod back in place and replace the nut
    • Replace the stabilizer link and bracket. Tighten the nut
    • Put the ABS sensor back in place
    • Jack the tie rod up and tighten the nut to 55 to 60ft/lbs
    • Replace the wheel and thread the lug nuts
    • Lower the car and tighten the lug nuts to 100ft/lbs in a crossing pattern
    • Tighten the bolts in the engine compartment to between 25 and 30ft/lbs

Tools needed for replacement:

    General Tools

  • Hammer

  • Materials, Fluids, and Supplies

  • Rust Penetrant

  • Ratchets & Related

  • 1/2 Inch Breaker Bar
  • Ratchet
  • Socket Extensions
  • Torque Wrench

  • Sockets - Metric

  • 13mm Socket
  • 15mm Socket
  • 17mm Socket
  • 19mm Socket

  • Torx Drivers & Sockets

  • T30 Torx Driver

  • Wrenches - Metric

  • 17mm Wrench

There are no reviews for this item.
Will this fit my car? Add a vehicle to make sure
Customer Q&A
Ask a question to 1A Auto customers who purchased the product
Does it come with all new hardware or do you have to reuse some from oem parts?
Tony L June 19, 2017
You will need to reuse the factory hardware.
Alex P June 20, 2017
Year Make Model Description
2000-2007Ford Focus Ford Focus Sedan Rear Shock Absorber Pair TRQ SBA60342
2000-2007Ford Focus Ford Focus Hatchback Rear Shock Absorber Pair TRQ SBA60342
2008-2011Ford Focus Ford Focus Rear Shock Absorber Pair TRQ SBA60342
Part #: 1ASSP00799


Order must be placed by 4pm ET

Get it in: 2 - 4 Business Days

Want it sooner? Choose Next Day Air at Checkout

TRQ
Brand #: SBA60342

How-to Video:

(13:03 min)