Replaces

Ford F150 Truck Wheel Bearing & Hub Assembly TRQ BHA53952 - 1ASHF00086

Specifications:

  • Fits either LH (Driver Side) or RH (Passenger Side) FRONT
  • 3 Bolt Flange
  • Fits 5 Lug Wheel
  • Replaces dealer part numbers: F65Z1104BA, F65Z-1104BA, F75W1104EA, F75W-1104EA, XL341104BB, XL34-1104BB, XL341104BD, XL34-1104BD, XL3Z1104BC, XL3Z-1104BC
  • Studs already installed (Studs are M12's (12mm))
  • Direct replacement
  • Built to strict quality control standards
  • Fits 4WD (Four Wheel Drive) Models only
  • Fits models with RWAL (Rear Wheel Anti-Lock Brakes) only

Quality

  • You will not have a problem with our product. If you are comparing us to someone selling a brand name product remember brand names are only as good as the company selling them. Both Bizrate.com and The Better Business Bureau recognize 1A Auto as a trusted online seller. You will be pleased with what you find out about us.
  • You don't want to be delayed by a defective part. 1A Auto wheel hub & bearings are all tested prior to shipping.

Fit Guaranteed

  • This hub & bearing will install just as your original does. You can use your existing hardware.
  • Save time and money with this direct fit hub bearing assembly. No trips to the auto parts store or extra time trying to match up and press bearings.
  • Hub installation is a degree more difficult than changing a tire on most vehicles.

Value

  • Some shops and dealers charge more for parts and repairs when they think the customer doesn't know what is involved. Now you can get the value you deserve. Knowing what this repair entails can be the difference between the value of doing it yourself, or the pain of a costly part or repair bill.
Precision Engineered

From the highest grade SAE 1055 / 65Mn high carbon steel to exact OEM design.

100% Factory tested to precise OEM tolerances.

Highest Quality Materials

High quality, multi-lip seal reduces the intrusion of dirt and water. Heavy duty grease resists high temperature, moisture, and reduces intense friction.

Direct Fit Replacement

Guaranteed to fit and function correctly for your specific application.

Part Details

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

BHA53952 Axle / Spindle Nut Torque Specification

  1. step : Removing the Wheel (0:30)
    • Loosen the 19mm lug nuts with the vehicle on the ground
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the lug nuts
    • Pull off the wheel
  2. step : Removing the Hub Nut (1:00)
    • Straighten the cotter pin on the nut with needle nose pliers
    • Remove the cotter pin
    • Thread three or four lug nuts on
    • Hold the rotor still with a pry bar
    • Loosen the 35mm hub nut
  3. step : Removing the Brake Caliper (2:48)
    • Use a c-clamp to push in the pistons
    • Remove the 18mm bolts from the brake caliper bracket
    • Pull off the brake caliper bracket
    • Lift the caliper up and off to the side
    • Secure the caliper with a bungee cord
    • Remove the rotor
  4. step : Removing the Wheel Hub (5:02)
    • Remove the three 15mm bolts from the hub
    • Tap the wheel hub off with a hammer
    • If the axle end won't move, place a block of wood on the end and tap it in with a hammer
  5. step : Installing the Wheel Hub (9:38)
    • Apply grease to the axle shaft splines
    • Slide the wheel hub onto the axle shaft splines
    • Tighten the 15mm bolts
    • Torque the bolts to 110-148 foot-pounds
    • Reinstall the axle nut
    • Torque the axle nut to 188-254 foot-pounds
    • Slide in the cotter pin to the nut
    • Bend the cotter pin
  6. step : Installing the New Brake Pads (13:12)
    • Put the rotor on
    • Put the caliper on
    • Thread the 18mm bolts by hand
    • Tighten bolts to 136 foot-pounds
    • Clean the rotor with brake parts cleaner or mineral spirits
  7. step : Reattaching the Wheel (14:14)
    • Slide the wheel into place
    • Start the lug nuts by hand
    • Tighten the lug nuts preliminarily
    • Lower the vehicle to the ground
    • Tighten the lug nuts to 83-112 foot-pounds in a crossing or star pattern

Tools needed for replacement:

    General Tools

  • Large C-Clamp
  • Hammer
  • Jack Stands
  • Floor Jack

  • Materials, Fluids, and Supplies

  • Block of Wood
  • Bungee Cord

  • Pliers, Cutters & misc Wrenches

  • Needle nose pliers

  • Ratchets & Related

  • Torque Wrench
  • Ratchet
  • 1/2 Inch Breaker Bar

  • Screwdrivers & Related

  • Pry Bar

  • Sockets - Metric

  • 35mm Socket
  • 15mm Socket
  • 18mm Socket
  • 19mm Socket

5.0 / 5.0
1 Review
5 Stars
4 Stars
3 Stars
2 Stars
1 Star
1
0
0
0
0
Just what I ordered
I have found 1aauto the best at shipping with the least problems. This part I put on about a year ago and it’s still going strong
May 29, 2018
Purchased
10 months ago
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

  • 1997-1999 Ford F150 Truck 4 Wheel Drive Front Wheel Bearing & Hub Assembly for Models with Rear Wheel ABS Brakes TRQ
  • 2000 Ford F150 Truck 4 Wheel Drive Front Wheel Bearing & Hub Assembly for Models with 12mm Stud Size & Rear Wheel ABS Brakes TRQ

This part replaces:

  • OE # F75W1104EA
  • OE # XL341104BB
  • OE # F65Z1104BA
  • Hollander 538-01392B 538-01392A
  • TRQ BHA53952
Part #: 1ASHF00086

TRQ
Brand #: BHA53952

How-to Video:

(15:08 min)