Specifications:

  • Brand New Suspension Kit
  • Comes as an 8 Piece Kit
    • Fits LH (Driver Side) & RH (Passenger Side)
  • Direct replacement
  • Built to strict quality control standards

Our steering and suspension components come pre-greased, sealed for long life, and do not require the extra maintenance typically required by greasable versions.

Direct Fit

Application-specific, with no modifications required.

Rigorously Tested

Made from higher quality materials than the competition. Built to have a longer life in any environment or road conditions.

State of the Art Manufacturing

By the same factories that the OEMs use.

Prepackaged for Your Convenience

Carefully assembled to include all of the parts you need, saving time and money.

Part Details

  • Kit Includes: (2) Front Lower Ball Joints
  • Kit Includes: (2) Front Upper Control Arms with Ball Joints
  • Kit Includes: (2) Front Outer Tie Rods
  • Kit Includes: (2) Front Sway Bar Links
  • Quantity: 8 Piece Set

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

Please Note: Whenever replacing steering components, it is highly recommended to have a professional alignment performed on the vehicle afterwards.  Failure to do so may result in issues with steering and premature tire wear.

  1. step : Removing the Wheel (0:41)
    • Pry off the center cap with a flat blade screwdriver
    • Loosen the lug nuts with the vehicle on the ground
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the lug nuts
    • Pull off the wheel
  2. step : Removing the Outer Tie Rod (1:13)
    • Turn the wheel by hand
    • Remove the 21mm nut from the outer tie rod
    • Thread the 21mm nut on a couple of turns
    • Hold the tie rod with an adjustable wrench
    • Loosen the tie rod adjusting nut with an adjustable wrench
    • Strike the steering knuckle with a hammer
    • Twist the 21mm nut off the tie rod
    • Measure the distance from the tie rod boot to the outer tie rod stud
    • Note that measurement
    • Twist off the outer tie rod.
  3. step : Installing the Tie Rod (2:11)
    • Twist on the outer tie rod
    • Measure the distance from the tie rod boot to the outer tie rod stud
    • This should be the same as the distance noted in Step 2
    • Move the adjusting nut as necessary
    • Push the tie rod into the wheel knuckle
    • Fasten the 21mm nut onto the tie rod
    • Tighten the 21mm nut to 111 foot-pounds of torque
    • Tighten the adjusting nut
    • Twist the grease fitting into the tie rod
    • Tighten the grease fitting with a 7mm socket and ratchet
    • Add grease to the grease fitting with a grease gun
  4. step : Reattaching the Wheel (3:34)
    • Slide the wheel into place
    • Start the lug nuts by hand
    • Tighten the lug nuts preliminarily
    • Lower the vehicle to the ground
    • Tighten the lug nuts to 120 foot-pounds in a crossing or star pattern
    • Reattach the center cap

Tools needed for replacement:

    General Tools

  • Measuring Tape
  • Floor Jack
  • Hammer
  • Jack Stands

  • Materials, Fluids, and Supplies

  • Bearing Grease

  • Pliers, Cutters & misc Wrenches

  • Adjustable Wrench

  • Ratchets & Related

  • Ratchet
  • Torque Wrench

  • Sockets - Metric

  • 21mm Socket
  • 7mm Socket
  • 10mm Socket

  • Specialty Tools

  • Grease Gun

  • Wrenches - Metric

  • 21mm wrench

There are no reviews for this item. Write Review
Start typing your question and we'll check if it was already asked and answered. Learn More
Browse 1 question Browse 1 question and 2 answers
Will this fit my 2003 Eddie Bauer expedition with out air suspension ?
salvador j on May 26, 2016
BEST ANSWER: 2003 Ford Expedition 8 Piece Set Suspension Kit with (2) Front Upper Control Arms with Ball Joints (2) Front Lower Ball Joints (2) Front Outer Tie Rods & (2) Front Sway Bar Links

(excluding Air Suspension)
Yes, according to the information you supplied, the part you’re looking at will be correct for your vehicle. If you have any other questions or would like to place an order with one of our customer service representatives, please feel free to give us a call.

Vehicle Fit

Year Make Model Description
2003Ford Expedition Ford Expedition 8 Piece Set Suspension Kit without Air Suspension
2004Ford Expedition Ford Expedition (Built Before 12/02/03 Production Date) 8 Piece Set Suspension Kit without Air Suspension

This part replaces:

  • Dorman 521-041
  • Dorman 521-042
  • Hollander 511-01073L
  • Hollander 511-01072R
  • OE # 2L1Z3A130CA, 6L1Z3A130A
  • OE # 2L1Z5K483AD, 2L1Z5K483AA
  • OE # 2L1Z3085AA
  • OE # 2L1Z3084AA
  • Moog K80713
  • Moog K80712
  • Moog K500060
  • Moog K80239
  • Moog ES3695
Part #: 1ASFK02444


Order must be placed by 4pm ET

Get it in: 2 - 4 Business Days

Want it sooner? Choose Next Day Air at Checkout

How-to Video:

(04:25 min)