This combination wiper, high beam dimmer and turn signal switch lever is a new, aftermarket replacement part. It is designed to REPLACE original units that are prone to failure. It's just what you need to get your vehicle in good working order again!

Specifications:

  • Replaces dealer part number(s): F65Z-13K359AA , F65Z-13K359AA , Y85Z-13K359AA , Y85Z-13K359CA
  • Direct replacement
  • Design improved for more durability
  • Detailed graphics
  • Built to strict quality control standards

This combination lever is designed to replace your original with no modifications necessary.

Our electrical and electronic parts are subject to strict quality control testing .  Once the item has been installed or plugged in, it is no longer eligible for a refund.  The item may be eligible for replacement, only if it is found to have a manufacturing defect. Before purchasing, please ensure proper diagnosis of the failed original part is performed

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

  1. step : Removing the Steering Column Cover (0:51)
    • Turn the key to RUN position
    • Press the detent ball in the cylinder by inserting a pick into the bottom of the column
    • Remove the three Phillips head screws from the holes in the column
    • Tilt the steering column down
    • Pop out the panel and remove it from the column
    • Tilt the column back up
    • Unscrew the lever from the column
    • Remove the column covers
  2. step : Removing the Multi-Function Switch (2:02)
    • Remove the lower T15 Torx screw
    • Pull the lever down
    • Remove the upper T15 Torx screw
    • Disconnect the multi-function switch
  3. step : Installing the Multi-Function Switch (4:15)
    • Insert the multi-function switch into place
    • Connect the wiring harness
    • Tighten the two T15 Torx screws
  4. step : Installing the Steering Column Cover (4:46)
    • Reinstall the two halves of the steering column cover
    • Tighten the three Phillips head screws to the cover
    • Reinstall the ignition cylinder
    • Turn it back and remove the key
    • Screw in the tilt column switch
    • Reinstall the rear cover

Tools needed for replacement:

    General Tools

  • Pick

  • Screwdrivers & Related

  • Phillips Head Screwdriver
  • Flat Blade Screwdriver

  • Torx Drivers & Sockets

  • T15 Torx Driver

5.0 / 5.0
6 Reviews
5 Stars
4 Stars
3 Stars
2 Stars
1 Stars
6
0
0
0
0
Not OEM, better than OEM.
I purchased this part on line and took a gamble because it was 1/3 the price of a factory replacement. I figure the savings would compensate for a shorter lifespan... Well I was wrong! The new part is heavier, beefier, and the electrical contacts are stronger than the factory original. This switch is a perfect fit and is even better quality than the factory part that my truck came with. That's impressive. My hazard lights and windshield washer all work again, and the turn signal lever is nicer than the original.
October 30, 2017
Perfect
It works fine; plug and play, simple install even a caveman can do it.
December 15, 2017
Purchased
2 months ago
Correct and Affordable
Correct and Affordable, Part fit and repaired the problem of intermittent headlights.
February 3, 2017
Purchased
1 year ago
Just as expected! Works great so far and installation was fairly straight forward.
November 29, 2017
Purchased
3 months ago
perfect match
GGot part fast and a perfect match. The installation video showed how to install it
February 3, 2018
Purchased
4 weeks ago
Exactly as ordered. Video was spot on in telling me how to replace the part and I was able to do it in about 30 minutes. No issues. I'm about to start looking here for more parts to fix some nagging issues I've had with truck!!
January 26, 2018
Purchased
1 month ago
Start typing your question and we'll check if it was already asked and answered. Learn More
Browse 1 question Browse 1 question and 8 answers
Does the mentioned switch have the intermittent wiper delay ?
Johnny H on Oct 21, 2015
BEST ANSWER: My 1994 F150 wipers work sometimes and sometimes I have wiggle the switch. Will replacing this switch fix this problem? Are there instructions on how to replace the switch?

How-to Video:

(05:33 min)

Tools List:

    General Tools

  • Pick

  • Screwdrivers & Related

  • Phillips Head Screwdriver
  • Flat Blade Screwdriver

  • Torx Drivers & Sockets

  • T15 Torx Driver



This part replaces:

  • Standard Motor Products DS-749

Vehicle Fit

  • 1997 Ford F150 Truck Under 8500LB GVW Combination Switch
  • 1998 Ford F150 Truck Combination Switch
  • 1997-1998 Ford F250 Light Duty Truck Combination Switch
  • 1999-2000 Ford F250 Super Duty Truck Combination Switch
  • 1999-2000 Ford F350 Super Duty Truck Combination Switch
Part #: 1AZCC00017

Ships Same Day for orders placed by 4 P.M. ET

We're here to help

1A Auto Parts

Customer Feedback

"Thanks for the fast reliable service. Great price, and the headlights were as good as oem or better!!! Keep up the good work..."
- Dwuan M.
Read More