Replaces

Ford Brake Rotor Pair Nakamoto 54078-DSZ - 1APBR00007

These front performance brake rotors are just what you need to get your vehicle stopping great again!

Specifications:

  • Comes as a matched pair
    • Includes both LH (Driver) & RH (Passenger) Side FRONT
  • Cross drilled, Slotted, And Zinc Coated
  • Replaces dealer part number: F81Z-1125-DA, F81Z1125DA
  • 13mm Thick Hub Flange
  • Direct replacement
  • 8 Wheel Stud Holes
  • Fits 4WD (Four Wheel Drive) Models only
NOTE: For F450SD and F550SD Models: This hub has a 13mm Thick Hub Flange. Do not interchange with models with 10mm Thick Flange. According to Ford TSB 99-12-12, using the incorrect rotor will cause the rotors to drag.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

Wear and Tear

This item is backed by a warranty against defects in materials and workmanship under its intended use. The warranty does not cover normal wear and tear. Please keep your invoice for proof of this warranty.

  1. step : Removing the Wheel (0:49)
    • Pry off the center cap with a flat blade screwdriver
    • Loosen the lug nuts with the vehicle on the ground
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the 21mm lug nuts
    • Pull off the wheel
  2. step : Removing the Brake Pads (1:16)
    • Remove the two 17mm bolts from the brake caliper
    • Pry the brake pads into the caliper with a flat blade screwdriver to push in the pistons
    • Pull the caliper aside
    • Pull the two springs off of the brake pads
    • Pry the brake pads off with a flat blade screwdriver
  3. step : Removing the Brake Rotor (2:16)
    • Remove the two 21mm bolts from the brake caliper bracket
    • Pull off the brake caliper bracket
    • Strike the rotor with a hammer to loosen it
    • Pull the rotor off
  4. step : Preparing the New Brake Pads and Rotors (2:50)
    • Clean the rotor with brake parts cleaner
    • Apply grease to the brake pad tabs
    • Apply grease to the caliper slides
  5. step : Installing the New Brake Rotor (4:06)
    • Slide the rotor on
    • Put the bracket back into place
    • Start the two 21mm bolts by hand
    • Tighten the 21mm bolts to 100 foot-pounds of torque
  6. step : Installing the New Brake Pads (4:40)
    • Install the new brake pads into the bracket
    • Push on the brake pad springs
    • Put an old pad in the caliper
    • Use a large C-clamp and the old pad to push the pistons back
    • Put the caliper on
    • Thread the two 17mm bolts by hand
    • Tighten the 17mm bolts to 60 foot-pounds
  7. step : Reattaching the Wheel (6:13)
    • Slide the wheel into place
    • Start the lug nuts by hand
    • Tighten the lug nuts preliminarily
    • Lower the vehicle to the ground
    • Tighten the lug nuts to 100 foot-pounds in a crossing or star pattern
    • Reattach the center cap
  8. step : Testing the Brakes (7:11)
    • Check the brake fluid level
    • Add brake fluid if necessary
    • Pump your brakes repeatedly until they feel firm
    • Test your brakes at 5 miles per hour and then 10 miles per hour
    • Road test the vehicle

Tools needed for replacement:

    General Tools

  • Jack Stands
  • Large C-Clamp
  • Hammer
  • Floor Jack

  • Materials, Fluids, and Supplies

  • Cloth Rags
  • Brake Parts Cleaner
  • Bearing Grease
  • Brake Fluid

  • Ratchets & Related

  • Ratchet
  • A Piece of Pipe (for leverage)
  • Torque Wrench

  • Screwdrivers & Related

  • Flat Blade Screwdriver

  • Sockets - Metric

  • 17mm Socket
  • 21mm Socket

There are no reviews for this item. Write Review
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

How-to Video:

(07:45 min)

Tools List:

    General Tools

  • Jack Stands
  • Large C-Clamp
  • Hammer
  • Floor Jack

  • Materials, Fluids, and Supplies

  • Cloth Rags
  • Brake Parts Cleaner
  • Bearing Grease
  • Brake Fluid

  • Ratchets & Related

  • Ratchet
  • A Piece of Pipe (for leverage)
  • Torque Wrench

  • Screwdrivers & Related

  • Flat Blade Screwdriver

  • Sockets - Metric

  • 17mm Socket
  • 21mm Socket



This part replaces:

  • Nakamoto 54078-DSZ

Vehicle Fit

  • 2000-2004 Ford Excursion 4 Wheel Drive Front Cross Drilled & Slotted Zinc Coated Brake Rotor Pair Performance Nakamoto
  • 2005 Ford Excursion 4 Wheel Drive Front Cross Drilled & Slotted Zinc Coated Brake Rotor Pair for Models with 4 Wheel ABS Brakes Performance Nakamoto
  • 1999 Ford F250 Super Duty Truck 4 Wheel Drive Front Cross Drilled & Slotted Zinc Coated Brake Rotor Pair (Built After 3/22/99 Production Date) Performance Nakamoto
  • 2000-2004 Ford F250 Super Duty Truck 4 Wheel Drive Front Cross Drilled & Slotted Zinc Coated Brake Rotor Pair Performance Nakamoto
  • 1999 Ford F350 Super Duty Truck 4 Wheel Drive Front Cross Drilled & Slotted Zinc Coated Brake Rotor Pair (Built After 3/22/99 Production Date) 13" (330mm) Diameter Rotors Performance Nakamoto
  • 2000 Ford F350 Super Duty Truck 4 Wheel Drive Front Cross Drilled & Slotted Zinc Coated Brake Rotor Pair 13" (330mm) Diameter Rotors Performance Nakamoto
  • 2001-2004 Ford F350 Super Duty Truck 4 Wheel Drive Front Cross Drilled & Slotted Zinc Coated Brake Rotor Pair for Models with 4 Wheel ABS Brakes 13" (330mm) Diameter Rotors Performance Nakamoto
  • 2001-2002 Ford F450 Truck 4 Wheel Drive Front Cross Drilled & Slotted Zinc Coated Brake Rotor Pair 13" (330mm) Diameter Rotors Performance Nakamoto
  • 2003 Ford F450 Truck 4 Wheel Drive Front Cross Drilled & Slotted Zinc Coated Brake Rotor Pair for Models with Axle ID 2C34-3002 13" (330mm) Diameter Rotors Performance Nakamoto
  • 2000-2002 Ford F550 Truck 4 Wheel Drive Front Cross Drilled & Slotted Zinc Coated Brake Rotor Pair 13" (330mm) Diameter Rotors Performance Nakamoto
  • 2003 Ford F550 Truck 4 Wheel Drive Front Cross Drilled & Slotted Zinc Coated Brake Rotor Pair for Models with Axle ID 2C34-3002 13" (330mm) Diameter Rotors Performance Nakamoto
Part #: 1APBR00007

Ships Same Day for orders placed by 4 P.M. ET

Nakamoto
Brand #: 54078-DSZ

We're here to help

1A Auto Parts

Customer Feedback

"Thanks for the fast reliable service. Great price, and the headlights were as good as oem or better!!! Keep up the good work..."
- Dwuan M.
Read More