These replacement door handles are just what you need to get your vehicle in good looking form again!

Specifications:

  • Come as a PAIR
    • Fits both the LH (Driver Side) & RH (Passenger Side) FRONT
  • Replaces dealer part numbers: 94852496, 69220-12160, 6922012160, 69210-12160, 6921012160
  • Injection molded Textured black plastic
  • Durable construction
  • Steel center rods and return springs
  • Direct replacements for original handles
  • Fit 4 door sedan and station wagon models only

These exterior door handles are direct bolt ons and are built to strict quality control standards. They are great replacements and have substantial cost savings over dealer units.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

  1. step : Remove the door panel (0:27)
    • Remove the Phillips screw in the inside door handle.
    • Unclip the door latch rod.
    • Pry up the corner panel on the inside side of the side mirror.
    • With your screwdrivers, pry up the top of the door pull and remove the two Phillips screws.
    • Pry up the switch panel and unplug it.
    • Use a putty knife to unclip the door panel from the door.
    • Carefully peel back the water shield.
  2. step : Remove the outside door handle (2:30)
    • Unbolt the four 10 mm bolts and the one nut to remove the bracket in the door.
    • Reach into the door and unclip the lock and latch rods from the door handle.
    • Remove the two 10 mm bolts in the door handle.
    • Pull the lock cylinder out .
    • Remove the door handle.
  3. step : Install the new door handle (4:51)
    • Start bolting in the door handle, putting the lock cylinder in before you finish bolting down the far bolt.
    • Clip in the lock and latch rods to the door handle.
    • Bolt that bracket back in with your 10 mm socket and ratchet.
  4. step : Put the door panel back on (7:25)
    • Clip the door panel in, threading the wiring connectors through the door pull.
    • Fasten all the Phillips screws.
    • Plug in the wiring harness to the switch panel.
    • Clip the switch panel and top of the door pull down.
    • Connect the door latch with the lock and latch rods.

Tools needed for replacement:

    General Tools

  • Putty Knife

  • Ratchets & Related

  • Ratchet

  • Screwdrivers & Related

  • Phillips Head Screwdriver
  • Flat Blade Screwdriver

  • Sockets - Metric

  • 10mm Socket

  • Wrenches - Metric

  • 10mm Wrench

5.0 / 5.0
1 Review
5 Stars
4 Stars
3 Stars
2 Stars
1 Stars
1
0
0
0
0
Perfect fit.
These parts match the stock parts perfectly. I watched the 1A Auto videos and installation was a breeze.
July 12, 2017
Purchased
11 months ago
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

  • 1993-1997 Geo Prizm 4 Door Black Textured Exterior Door Handle Front Pair
  • 1993-1997 Toyota Corolla 4 Door Black Textured Exterior Door Handle Front Pair
  • 1996-2000 Toyota Rav4 4 Door Black Textured Exterior Door Handle Front Pair

This part replaces:

  • OE # 6921012160
  • OE # 6922012160
Part #: 1ADHS00383

How-to Video:

(09:20 min)