Replaces

Drive Belt Component Kit Gates ACK070763 - GAEEK00187

Gates Micro-V Component Kit (ACK070763) 

This Gates Accessory Drive Belt Kit is just what you need to keep your vehicle in good running order.

Gates has developed this complete all in one kit for easy drive belt system restoration. All components are bundled specifically for each application to ensure that the accessory drive belt system will operates flawlessly.

Specifications:

  • Includes:
    • (1) - Micro-V Serpentine Belt
    • (1) - DriveAlign Belt Tensioner
  • Built to strict quality control standards

Sometimes replacing just the serpentine belt is not enough. Avoid System breakdown with this complete kit.

 

These parts are authentic Gates brand products that are supplied and packaged by Gates. Some of the components included in this kit may be sourced by Gates from other high quality suppliers such as Aisin, GMB, Koyo & other OEM suppliers. These parts are subjected to the very same testing and quality standards as all Gates products.

2 Year Warranty

This item is backed by a 2 Year Warranty. In the event this item should fail during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

Wear and Tear

This item is backed by a warranty against defects in materials and workmanship under its intended use. The warranty does not cover normal wear and tear. Please keep your invoice for proof of this warranty.

  1. step : Removing the Serpentine Belt (0:27)
    • Familiarize yourself with the route of the serpentine belt
    • Insert a breaker bar and 19mm socket into the tensioner
    • Slowly turn the tensioner clockwise to loosen the belt
    • Pull the belt off the alternator
    • Slowly release the tensioner
    • Remove the serpentine belt
  2. step : Removing the Front Passenger Side Wheel (3:32)
    • Loosen the lug nuts with the vehicle on the ground
    • Raise and support the vehicle
    • Remove the lug nuts
    • Pry off the center cap with a flat blade screwdriver
    • Apply rust penetrant to the wheel studs
    • Thread two lug nuts lightly onto the studs
    • Strike the tire with a rubber mallet or dead blow hammer to loosen the wheel
    • Remove the two lug nuts
    • Pull the wheel off the studs
  3. step : Removing the Serpentine Belt Tensioner (5:39)
    • Remove the fasteners from the belt shield
    • Pull off the belt shield
    • Loosen the 14mm nut at the bottom of the tensioner
    • Loosen the 14mm bolt at the top of the tensioner
    • Remove the 14mm nut
    • Remove the tensioner from the engine
  4. step : Installing the Serpentine Belt Tensioner (7:28)
    • Thread the 14mm bolt through the top of the tensioner
    • Maneuver the tensioner into place on the engine
    • Line up the bottom of the tensioner with the stud
    • Push the tensioner onto the stud with a pry bar
    • Start the 14mm bolt
    • Fasten the 14mm nut onto the stud
    • Tighten the 14mm bolt
  5. step : Reinstalling the Serpentine Belt (9:53)
    • Loop the belt around the crank pulley
    • Bring it around the power steering pulley
    • Bring it around the water pump
    • Bring it around the A/C Pulley
    • Bring it around the crank shaft pulley
    • Bring it around the belt tensioner
    • Slowly pull the tensioner clockwise with a 19mm socket and breaker bar
    • Pull the belt over the alternator
    • Slowly release the tensioner
  6. step : Installing the Wheel (10:45)
    • Lift the wheel onto the studs
    • Start the lug nuts by hand
    • Lower the vehicle to the ground
    • Torque the lug nuts to 76 foot-pounds in a crossing pattern
    • Clip the center cap onto the wheel

Tools needed for replacement:

    General Tools

  • Jack Stands
  • Rubber Mallet
  • Floor Jack

  • Materials, Fluids, and Supplies

  • Rust Penetrant

  • Ratchets & Related

  • Torque Wrench
  • Ratchet
  • 1/2 Inch Breaker Bar

  • Screwdrivers & Related

  • Pry Bar
  • Flat Blade Screwdriver

  • Sockets - Metric

  • 19mm Socket
  • 21mm Socket

  • Specialty Tools

  • Dead Blow Hammer

  • Wrenches - Metric

  • 14mm Wrench

There are no reviews for this item. Write Review
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

  • 2005-2006 Scion tC Drive Belt Component Kit L4 2.4L (excluding Supercharged Models) Gates ACK070763
  • 2002-2006 Toyota Camry Drive Belt Component Kit L4 2.4L Gates ACK070763
  • 2001-2007 Toyota Highlander Drive Belt Component Kit L4 2.4L Gates ACK070763
  • 2001-2003 Toyota Rav4 Drive Belt Component Kit L4 2.0L Gates ACK070763
  • 2004-2005 Toyota Rav4 Drive Belt Component Kit L4 2.4L with with Air Conditioning Gates ACK070763
  • 2002-2007 Toyota Solara Drive Belt Component Kit L4 2.4L Gates ACK070763

This part replaces:

  • Gates ACK070763
Only 3 left in stock
Part #: GAEEK00187

GATES
Brand #: ACK070763

How-to Video:

(11:37 min)