Specifications:

  • Brand New Steering & Suspension Kit
  • Comes as a Set of 14
  • Direct replacements
  • Built to strict quality control standards

Our steering and suspension components come pre-greased, sealed for long life, and do not require the extra maintenance typically required by greasable versions.

Direct Fit

Application-specific, with no modifications required.

Rigorously Tested

Made from higher quality materials than the competition. Built to have a longer life in any environment or road conditions.

State of the Art Manufacturing

By the same factories that the OEMs use.

Prepackaged for Your Convenience

Carefully assembled to include all of the parts you need, saving time and money.

Part Details

  • Kit Includes: (2) Front Upper Forward Control Arms with Ball Joints
  • Kit Includes: (2) Front Lower Ball Joints
  • Kit Includes: (2) Front Outer Tie Rods
  • Kit Includes: (2) Front Sway Bar Links
  • Kit Includes: (2) Rear Sway Bar Links
  • Kit Includes: (2) Steering Rack & Pinion Bellows
  • Quantity: 14 Piece Set
  • Kit Includes: (2) Front Inner Tie Rods

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

Please Note: Whenever replacing steering components, it is highly recommended to have a professional alignment performed on the vehicle afterwards.  Failure to do so may result in issues with steering and premature tire wear.

  1. step : Removing the Wheel (0:38)
    • Loosen the 22mm lug nuts with the vehicle on the ground
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the lug nuts
    • Pull off the wheel
  2. step : Removing the Outer Tie Rod (1:49)
    • Loosen the 24mm nut that holds the outer tie rod to the inner tie rod with an adjustable wrench
    • Remove the 22mm nut from the outer tie rod end
    • Strike the steering knuckle with a hammer to loosen the outer tie rod
    • Pull the outer tie rod out of the steering knuckle
    • Twist off the outer tie rod by hand
  3. step : Installing the New Outer Tie Rod (3:49)
    • Twist the new outer tie rod onto the inner tie rod
    • Push the outer tie rod into the steering knuckle
    • Fasten the 22mm castle nut onto the outer tie rod
    • Torque the nut to 45 foot-pounds, then torque to an additional 90 degrees
    • Push the cotter pin through the castle nut
    • Twist the cotter pin into place with needle nose pliers
    • Tighten the 24mm nut that holds the outer tie rod to the inner tie rod with an adjustable wrench
  4. step : Reattaching the Wheel (5:08)
    • Slide the wheel into place
    • Start the 22mm lug nuts by hand
    • Tighten the lug nuts preliminarily
    • Lower the vehicle to the ground
    • Tighten the lug nuts to between 135 foot-pounds in a crossing or star pattern

Tools needed for replacement:

    General Tools

  • Jack Stands
  • Floor Jack

  • Ratchets & Related

  • Ratchet
  • Torque Wrench
  • Socket Extensions
  • 1/2 Inch Breaker Bar

  • Sockets - Metric

  • 22mm Socket

  • Wrenches - Metric

  • 24mm Wrench

There are no reviews for this item. Write Review
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

  • 2004 Dodge Ram 2500 Truck 2 Wheel Drive Steering & Suspension Kit 14 Piece Set
  • 2004-2006 Dodge Ram 3500 Truck 2 Wheel Drive Steering & Suspension Kit 14 Piece Set

This part replaces:

  • Moog K80901
  • Moog ES3538
  • Dorman 520-199
  • Hollander 511-01068
  • OE # 5086980AA, 5170824AB
  • OE # 5072934AE, 5086972AB
  • OE # 52106776AB
  • OE # 5290373AA
  • OE # 68040228AA, 52121926AB
  • Moog K7462
  • Moog K7465
  • Moog K80821
  • Moog EV80211
  • OE # 521104
Part #: 1ASFK04476


Order must be placed by 4pm ET

How-to Video:

(06:11 min)