Replaces

Dodge Ram 1500 Truck Wheel Bearing & Hub Assembly Timken HA500100 - TKSHF00065

Description
Warranty & Shipping
How-To & Tools
Product Reviews
Q&A
Vehicle Fit

TIMKEN WHEEL BEARING & HUB ASSEMBLY: HA500100

Specifications:

  • Brand New Timken Wheel Bearing & Hub Assembly
  • Fits either LH (Driver Side) or RH (Passenger Side) FRONT
  • 3 Bolt Flange
  • Fits 5 Lug Wheel
  • Replaces dealer part number: 52070321AA, 52070321AB
  • Direct replacement
  • Studs already installed
  • Does NOT fit the LH (Driver Side) on models that use a Speed Sensor
  • Fits models with RWAL (Rear Wheel Anti-Lock Brakes) only
    • Does NOT fit models with 4 Wheel ABS

NOTE: 2004-07 Ram 1500 V8 5.7L Models: The speed sensor is only on the LH (Driver Side) wheel bearing. Please verify there is no speed sensor on the LH (Driver Side) bearing before ordering.

Note:
These parts are authentic Timken brand products that are supplied and packaged by Timken.   In some cases, Timken will source parts from other high quality suppliers such as SKF and Koyo. These parts are subjected to the very same testing and quality standards as all Timken products.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

  1. step : Remove the wheel and tire (1:13)
    • Raise and secure the vehicle.
    • Remove the lug nuts and then the wheel.
  2. step : Remove Caliper (1:40)
    • Turn wheels all the way in the opposite direction of the side you are working on.
    • Use your socket wrench to remove the caliper bolts.
    • Use a wire tie to help prevent stress on the caliper.
    • Use your socket to remove the brackets.
  3. step : Remove brake disk (3:00)
    • Take care not to touch the rotor, and if you do make sure to clean it with rubbing alcohol or mineral spirits.
  4. step : Remove Hub (3:16)
    • Use a 35mm socket to remove the hub nut.
    • Give the axle a slight tap with a hammer to loosen it.
    • Use a pry bar to remove the axle.
    • Remove the 3 bolts securing the hub using your 18mm socket and extension and ratchet or breaker bar.
    • You can use penetrating oil to help.
    • Disconnect your ABS sensor.
    • Use a rubber mallet to break your hub free, and work around the flange with the hammer to pull it off.
    • Remove the hub and shield.
    • Clean up any corrosion with a wire brush.
  5. step : Install new hub (9:26)
    • Use some penetrating oil to prep the knuckle for the new hub.
    • Put the three 18 mm bolts in place and tighten the nuts to 100 ft lbs.
    • Reinstall the ABS harness.
    • Replace the axle.
    • Tighten but don't torque the lug nut.
  6. step : Put brakes and wheel back on (11:40)
    • Remember to replace the lug nuts on in a star pattern.
    • Lug nuts tighten to 120 ft lbs
    • Hub nut is 185 ft lbs.
    • Make sure to check your brakes and steering before driving again.
    • Make sure to pump the brakes and seat your rotors.

Tools needed for replacement:

    General Tools

  • Floor Jack
  • Jack Stands
  • Large C-Clamp
  • Wire Brush

  • Ratchets & Related

  • 1/2 Inch Breaker Bar
  • Ratchet
  • Socket Extensions
  • Torque Wrench

  • Screwdrivers & Related

  • Flat Blade Screwdriver

  • Sockets - Metric

  • 13mm Socket
  • 18mm Socket

  • Sockets - SAE

  • 13/16 Inch Socket
  • 7/8 Inch Socket

5.00/ 5.0
1review
5 Stars
4 Stars
3 Stars
2 Stars
1 Star
1
0
0
0
0
Timken Hub
This is a quality product. Dont waste your money on China hubs. Buy this once, and forget about it.
February 9, 2017
Will this fit my car? Add a vehicle to make sure
Customer Q&A
Ask a question to 1A Auto customers who purchased the product
No questions have been asked about this item.
Year Make Model Description
2002-2005Dodge Ram 1500 Truck Dodge Ram 1500 Truck Front Wheel Bearing & Hub Assembly for Models with Rear Wheel ABS Brakes Timken HA500100
2006-2008Dodge Ram 1500 Truck Dodge Ram 1500 Truck Quad Cab Front Wheel Bearing & Hub Assembly for Models with Rear Wheel ABS Brakes Driver Side without Speed Sensor Timken HA500100
2006-2008Dodge Ram 1500 Truck Dodge Ram 1500 Truck Quad Cab Front Wheel Bearing & Hub Assembly for Models with Rear Wheel ABS Brakes Passenger Side Timken HA500100
2006-2008Dodge Ram 1500 Truck Dodge Ram 1500 Truck Regular Cab Front Wheel Bearing & Hub Assembly for Models with Rear Wheel ABS Brakes Driver Side without Speed Sensor Timken HA500100
2006-2008Dodge Ram 1500 Truck Dodge Ram 1500 Truck Regular Cab Front Wheel Bearing & Hub Assembly for Models with Rear Wheel ABS Brakes Passenger Side Timken HA500100
Only 2 left in stock
Part #: TKSHF00065


Order must be placed by 4pm ET

Get it in: 2 - 4 Business Days

Want it sooner? Choose Next Day Air at Checkout

Timken
Brand #: HA500100

How-to Video:

(13:39 min)