Replaces

Dodge Ram 1500 Truck Wheel Bearing & Hub Assembly Pair TRQ BHA53504 - 1ASHS00369

Specifications:

  • Comes as a PAIR
    • Fits both LH (Driver Side) & RH (Passenger Side) FRONT
  • 3 Bolt Flanges
  • Fit 5 Lug Wheels
  • Replaces dealer part numbers: 52070321AA, 52070321AB
  • Studs already installed
  • Direct replacements
  • Does NOT fit the LH (Driver Side) on models that use a Speed Sensor
  • Fit models with RWAL (Rear Wheel Anti-Lock Brakes) only
    • Does NOT fit models with 4 Wheel ABS

NOTE: 2004-07 Ram 1500 V8 5.7L Models: The speed sensor is only on the LH (Driver Side) wheel bearing. Please verify there is no speed sensor on the LH (Driver Side) bearing before ordering.

Precision Engineered:

From the highest grade SAE 1055 / 65Mn high carbon steel to exact OEM design.
100% Factory tested to precise OEM tolerances.

Highest Quality Materials:

High quality, multi-lip seal reduces the intrusion of dirt and water. Heavy duty grease resists high temperature, moisture, and reduces intense friction.

Direct Fit Replacement:

Guaranteed to fit and function correctly for your specific application.

Part Details

  • Quantity: Pair

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

BHA53944 Axle / Spindle Nut Torque Specification

  1. step : Remove the wheel and tire (1:13)
    • Raise and secure the vehicle.
    • Remove the lug nuts and then the wheel.
  2. step : Remove Caliper (1:40)
    • Turn wheels all the way in the opposite direction of the side you are working on.
    • Use your socket wrench to remove the caliper bolts.
    • Use a wire tie to help prevent stress on the caliper.
    • Use your socket to remove the brackets.
  3. step : Remove brake disk (3:00)
    • Take care not to touch the rotor, and if you do make sure to clean it with rubbing alcohol or mineral spirits.
  4. step : Remove Hub (3:16)
    • Use a 35mm socket to remove the hub nut.
    • Give the axle a slight tap with a hammer to loosen it.
    • Use a pry bar to remove the axle.
    • Remove the 3 bolts securing the hub using your 18mm socket and extension and ratchet or breaker bar.
    • You can use penetrating oil to help.
    • Disconnect your ABS sensor.
    • Use a rubber mallet to break your hub free, and work around the flange with the hammer to pull it off.
    • Remove the hub and shield.
    • Clean up any corrosion with a wire brush.
  5. step : Install new hub (9:26)
    • Use some penetrating oil to prep the knuckle for the new hub.
    • Put the three 18 mm bolts in place and tighten the nuts to 100 ft lbs.
    • Reinstall the ABS harness.
    • Replace the axle.
    • Tighten but don't torque the lug nut.
  6. step : Put brakes and wheel back on (11:40)
    • Remember to replace the lug nuts on in a star pattern.
    • Lug nuts tighten to 120 ft lbs
    • Hub nut is 185 ft lbs.
    • Make sure to check your brakes and steering before driving again.
    • Make sure to pump the brakes and seat your rotors.

Tools needed for replacement:

    General Tools

  • Floor Jack
  • Jack Stands
  • Large C-Clamp
  • Wire Brush

  • Ratchets & Related

  • 1/2 Inch Breaker Bar
  • Ratchet
  • Socket Extensions
  • Torque Wrench

  • Screwdrivers & Related

  • Flat Blade Screwdriver

  • Sockets - Metric

  • 13mm Socket
  • 18mm Socket

  • Sockets - SAE

  • 13/16 Inch Socket
  • 7/8 Inch Socket

5.0 / 5.0
4 Reviews
5 Stars
4 Stars
3 Stars
2 Stars
1 Star
4
0
0
0
0
Great
Went together nicely. Perfect fit and so far working as they should
May 3, 2018
Purchased
over 4 years ago
wheel hub assembly part # TQR BHA53504
I purchased two items {headlight assemblies and wheel hubs} for my 2003 Dodge 1500 truck from A1Auto, both items fit perfectly and were the right parts. I would recommended this website to anyone.
I was very please with the parts and delivery time.
April 9, 2018
Purchased
5 months ago
great
I put them right in no hassle so far so good hope they last longer than the last ones only got one year out of them came from autozone been in only 1 month time will tell
October 17, 2017
Purchased
10 months ago
Perfect Fit
Perfect fit for my 2 WD 07 Ram 1500 4.7 SLT. Installed with no problems and my truck is nice and quiet again. Ordered on Sunday and delivered Wednesday. Now for the test of time...
July 30, 2017
Purchased
1 year ago
Start typing your question and we'll check if it was already asked and answered. Learn More
Browse 3 questions Browse 3 questions and 9 answers
how good of quality is this bearing?
jimmy on Mar 11, 2016
BEST ANSWER: The quality is fantastic they were pretty easy to change and are working great. I would not hesitate to order them again if needed
Is this for a 2003 dodge 1500 2wd with 2 wheel abs ?
Adam H on Oct 3, 2017
BEST ANSWER: These will fit models with either two or four wheel drive, but is specific for models with rear wheel ABS only!
Does these work for a 4x4 truck?
Angie H on Sep 27, 2017
BEST ANSWER: This part is specific to vehicles with a particular set of options. We will need more information about your vehicle to confirm the fit. Please feel free to call our customer service department for clarification @ 888-844-3393.

Vehicle Fit

  • 2002-2005 Dodge Ram 1500 Truck Front Wheel Bearing & Hub Assembly for Models with Rear Wheel ABS Brakes Pair TRQ
  • 2006-2008 Dodge Ram 1500 Truck Quad Cab Front Wheel Bearing & Hub Assembly for Models with Rear Wheel ABS Brakes Pair without Speed Sensor TRQ
  • 2006-2008 Dodge Ram 1500 Truck Regular Cab Front Wheel Bearing & Hub Assembly for Models with Rear Wheel ABS Brakes Pair without Speed Sensor TRQ

This part replaces:

  • TRQ BHA53504
Part #: 1ASHS00369


Order must be placed by 4pm ET
TRQ
Brand #: BHA53504

How-to Video:

(13:39 min)