Replaces

Dodge Ram 1500 Truck Wheel Bearing & Hub Assembly Pair TRQ BHA53370 - 1ASHS00087

Specifications:

  • Comes as a PAIR
    • Fits both LH (Driver Side) & RH (Passenger Side) FRONT
  • 3 Bolt Flanges
  • Fit 5 Lug Wheels
  • Studs already installed
  • Include sensors
  • Direct replacements
  • Built to strict quality control standards

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

BHA53945 Axle / Spindle Nut Torque Specification
  1. step : Remove the wheel and tire (1:13)
    • Raise and secure the vehicle.
    • Remove the lug nuts and then the wheel.
  2. step : Remove Caliper (1:40)
    • Turn wheels all the way in the opposite direction of the side you are working on.
    • Use your socket wrench to remove the caliper bolts.
    • Use a wire tie to help prevent stress on the caliper.
    • Use your socket to remove the brackets.
  3. step : Remove brake disk (3:00)
    • Take care not to touch the rotor, and if you do make sure to clean it with rubbing alcohol or mineral spirits.
  4. step : Remove Hub (3:16)
    • Use a 35mm socket to remove the hub nut.
    • Give the axle a slight tap with a hammer to loosen it.
    • Use a pry bar to remove the axle.
    • Remove the 3 bolts securing the hub using your 18mm socket and extension and ratchet or breaker bar.
    • You can use penetrating oil to help.
    • Disconnect your ABS sensor.
    • Use a rubber mallet to break your hub free, and work around the flange with the hammer to pull it off.
    • Remove the hub and shield.
    • Clean up any corrosion with a wire brush.
  5. step : Install new hub (9:26)
    • Use some penetrating oil to prep the knuckle for the new hub.
    • Put the three 18 mm bolts in place and tighten the nuts to 100 ft lbs.
    • Reinstall the ABS harness.
    • Replace the axle.
    • Tighten but don't torque the lug nut.
  6. step : Put brakes and wheel back on (11:40)
    • Remember to replace the lug nuts on in a star pattern.
    • Lug nuts tighten to 120 ft lbs
    • Hub nut is 185 ft lbs.
    • Make sure to check your brakes and steering before driving again.
    • Make sure to pump the brakes and seat your rotors.

Tools needed for replacement:

    General Tools

  • Floor Jack
  • Jack Stands
  • Large C-Clamp
  • Wire Brush

  • Ratchets & Related

  • 1/2 Inch Breaker Bar
  • Ratchet
  • Socket Extensions
  • Torque Wrench

  • Screwdrivers & Related

  • Flat Blade Screwdriver

  • Sockets - Metric

  • 13mm Socket
  • 18mm Socket

  • Sockets - SAE

  • 13/16 Inch Socket
  • 7/8 Inch Socket

4.7 / 5.0
3 Reviews
5 Stars
4 Stars
3 Stars
2 Stars
1 Stars
2
1
0
0
0
it was easy to install the old one was hard to get off but the knew ones made up for the easy install
February 9, 2012
Great!
It was great to get the parts right away, and someone knowledgeable to answer my questions about it.
January 25, 2017
Purchased
1 year ago
so far so good
everything installed and seems to be working fine I ordered alot of parts with this order and was missing an upper control arm upon unpacking. customer service made it good and issued a credit. I will not hesitate to order from them again, and with a 15 year old truck I know I will be
October 12, 2017
Purchased
4 months ago
Start typing your question and we'll check if it was already asked and answered. Learn More
Browse 3 questions Browse 3 questions and 5 answers
Are these as good as Timken. Or at least as good as OEM?
DiggerDerrik on Sep 11, 2016
BEST ANSWER: They are comparable to oem, easy to install. Drive from Kentucky to New York with no issues. However, if you do a lot of off road driven Moog is best choice.
will these fit a 4wd?
Ken O on Jan 8, 2017
BEST ANSWER: This part is specific to vehicles with a particular set of options. We will need more information about your vehicle to confirm the fit. Please feel free to call our customer service department for clarification @ 888-844-3393.
what is the bolt size on the 3 bolt flange?
Bryon A on Aug 28, 2016
BEST ANSWER: Sorry we do not have the bolt specs avail.

How-to Video:

(13:39 min)

Tools List:

    General Tools

  • Floor Jack
  • Jack Stands
  • Large C-Clamp
  • Wire Brush

  • Ratchets & Related

  • 1/2 Inch Breaker Bar
  • Ratchet
  • Socket Extensions
  • Torque Wrench

  • Screwdrivers & Related

  • Flat Blade Screwdriver

  • Sockets - Metric

  • 13mm Socket
  • 18mm Socket

  • Sockets - SAE

  • 13/16 Inch Socket
  • 7/8 Inch Socket



This part replaces:

  • Hollander 538-01579
  • OE # 52070323AA
  • OE # 52070323AB
  • OE # 5083204AA
  • OE # 52070323AH
  • OE # 52070323AG
  • TRQ BHA53370

Vehicle Fit

  • 2002-2005 Dodge Ram 1500 Truck Front Wheel Bearing & Hub Assembly for Models with 4 Wheel ABS Brakes Pair TRQ
  • 2006 Dodge Ram 1500 Truck SLT Quad Cab 2 Wheel Drive Front Wheel Bearing & Hub Assembly for Models with 4 Wheel ABS Brakes Pair TRQ
  • 2006 Dodge Ram 1500 Truck SLT Regular Cab 2 Wheel Drive Front Wheel Bearing & Hub Assembly for Models with 4 Wheel ABS Brakes Pair TRQ
Part #: 1ASHS00087

Ships Same Day for orders placed by 4 P.M. ET

TRQ
Brand #: BHA53370

We're here to help

1A Auto Parts

Customer Feedback

"Thanks for the fast reliable service. Great price, and the headlights were as good as oem or better!!! Keep up the good work..."
- Dwuan M.
Read More