Replaces

Dodge Nitro Jeep Liberty Wheel Bearing & Hub Assembly Front TRQ BHA54090 - 1ASHF00403

Description
Warranty & Shipping
How-To & Tools
Product Reviews
Q&A
Vehicle Fit

Part Details

  • Wheel Bearing & Hub Assembly Features & Benefits:
      Direct Fit Replacement
      Precision Engineered
      Highest Quality Materials
  • Bearing Type:   Ball Bearing
  • Front or Rear Location:   Front

This replacement wheel bearing & hub assembly is just what you need to get your vehicle in good working order again.

Specifications:

  • Fits either LH (Driver Side) or RH (Passenger Side) FRONT
  • 3 Bolt Flange
  • Fits 5 Lug Wheel
  • Replaces dealer part numbers: 52109947AB, 52109947AC, 52109947AD, 52109947AE, 52109947AF
  • New wheel studs installed
  • Direct replacement
  • Built to strict quality control standards

This wheel bearing & hub assembly is a great replacement and has good cost savings over a unit from the dealer.

Item Condition: New

Attention California Customers:

WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

BHA54090 Axle / Spindle Nut Torque Specification

  1. step : Removing the Wheel (1:00)
    • Loosen the lug nuts with the vehicle on the ground
    • Remove the cotter pin from the axle nut if it has one
    • Loosen the axle nut
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the lug nuts
    • Pull off the wheel
  2. step : Removing the Brake Pads (3:22)
    • Remove the bolts from the caliper bracket
    • Pull the caliper off
    • Put the caliper aside
    • Pry the brake pads off with a flat blade screwdriver
  3. step : Removing the Brake Rotor (4:15)
    • Remove the two bolts from the caliper bracket
    • Pull off the brake caliper bracket
    • Remove a screw from the rotor if it has one
    • Strike the drum surface of the rotor with a hammer to loosen the rotor
    • Pull the rotor off
    • Clean the hub surface with a wire brush
  4. step : Removing the Hub Assembly (5:18)
    • Remove the axle bolt
    • Place a punch in the axle hole and hammer it to release the hub from the splines
    • Remove the bolts from the back of the hub
    • Remove the wheel hub and bearing
  5. step : Installing the Hub Assembly (7:53)
    • Insert the wheel hub into the spindle
    • Tighten the hub bolts
    • Reinstall the axle nut
  6. step : Installing the Brake Rotor (8:58)
    • Apply grease to the hub surface
    • Put the rotor onto the hub backwards
    • Spray the rear of the hub with brake cleaner
    • Pull off the brake rotor
    • Slide the brake rotor on
    • Spray the front of the rotor with brake cleaner
    • Put the caliper bracket into place
    • Insert the two into the caliper bracket
    • Torque the two bolts
  7. step : Installing the Brake Pads (9:48)
    • Put the brake pads into the caliper bracket
    • Apply grease to the back of the brake pads
    • Push back the caliper piston with grove lock pliers
    • Put the brake caliper into place
    • Insert the two bolts into the caliper
    • Torque the two bolts
  8. step : Reattaching the Wheel (11:01)
    • Slide the wheel into place
    • Start the lug nuts by hand
    • Tighten the lug nuts preliminarily
    • Lower the vehicle to the ground
    • Torque the lug nuts in a crossing or star pattern
    • Torque the axle nut

Tools needed for replacement:

    General Tools

  • Large C-Clamp
  • Chisel
  • Hammer

  • Materials, Fluids, and Supplies

  • Anti-Seize Grease

  • Ratchets & Related

  • Ratchet
  • Torque Wrench
  • Socket Extensions
  • 1/2 Inch Breaker Bar

  • Screwdrivers & Related

  • Flat Blade Screwdriver

  • Sockets - Metric

  • Complete Metric Socket Set

4.00/ 5.0
1review
5 Stars
4 Stars
3 Stars
2 Stars
1 Star
0
1
0
0
0
2010 Dodge Nitro hub assembly
This product worked great was fairly easy to install and watched the installation video to get some pointers took less than an hour start to finish.
March 22, 2017
Will this fit my car? Add a vehicle to make sure
Customer Q&A
Ask a question to 1A Auto customers who purchased the product
Who makes this part?
Billy F March 2, 2017
This is made by multiple manufacturers for us who are based in either Taiwan, China, or Japan to meet or exceed OE specifications and backed by a limited lifetime warranty.
Alex P March 2, 2017
I do not know the manufacturer. There were no markings on the part or the box other than 1As info. Part quality was as good as a Duralast assembly I purchased from another vendor. Part has been installed for about 5 weeks now with no issues.
John G March 9, 2017
Year Make Model Description
2007-2011Dodge Nitro Dodge Nitro Front Wheel Bearing & Hub Assembly TRQ
2008-2012Jeep Liberty Jeep Liberty Front Wheel Bearing & Hub Assembly TRQ
Part #: 1ASHF00403


Order must be placed by 4pm ET

Get it in: 2 - 4 Business Days

Want it sooner? Choose Next Day Air at Checkout

TRQ
Brand #: BHA54090

How-to Video:

(12:07 min)