Replaces

Dodge Mirror - 1AMRE01830

Description
Warranty & Shipping
How-To & Tools
Product Reviews
Q&A
Vehicle Fit

Part Details

  • Mirror Operation:   Power
  • Mirror Color / Finish:   Textured Black
  • Mirror Heating Type:   Heated

Specifications:

  • Fits RH (Passenger Side)
  • Power operation
  • Heated glass
  • Folding - Manual operation
  • Sail mount design - Mounts in the corner of the door
  • Injection molded black plastic housing
  • Direct replacement
  • Built to strict quality control standards

Special Note:

  • Unless otherwise noted, replacement mirrors will only work properly on vehicles with the exact same options. If your vehicle does not have the options listed in specifications, the mirror(s) may not function properly.

Item Condition: New

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

  1. step : Removing the Door Panel (1:06)
    • Remove the Phillips head screw inside the door handle
    • Remove the Phillips head screw at the front top corner of the door panel
    • Remove the two Phillips head screws on the bottom of the door panel
    • Lift the door panel up and off
    • Pop the lock bezel out
    • Pry up the window switch panel by hand
    • Disconnect the window switch wiring harnesses
    • Remove the four Phillips screws from the speaker
    • Pry off the speaker
    • Disconnect the speaker wiring lead
  2. step : Removing the Side Mirror (2:34)
    • Disconnect the mirror wiring harness
    • Remove the three 10mm nuts from the mirror
    • Have an assistant hold the mirror
    • Push in the clips on either side of the harness connection
    • Remove the mirror
  3. step : Removing the Protective Rubber Boot (3:18)
    • Pry up the door soleplate with a flat blade screwdriver
    • Pull the glove box down
    • Push in the tabs on either side of the glove box
    • Pull the glove box down and remove it from the hinge
    • Push in on the tabs on the body harness
    • Pry out and remove the body harness
    • Disconnect the wiring harness
    • Push the rubber boot through the door to release the harness
    • Carefully peel the top left corner of the water shield
  4. step : Removing the Dash Panel (4:58)
    • Remove the side dash panel by hand
    • Remove the screw from the pillar trim with a 4mm Allen wrench
    • Remove the pillar trim
    • Disconnect the dome harness
    • Remove the two Phillips screws from the lower dash panel
    • Pull out on the lower dash panel
  5. step : Installing the Power Fold and Light Wiring Harness (5:51)
    • Run one of the power fold harnesses behind the center and across to the passenger side
    • Feed the wire up through the dash and through the hole on the body
    • Repeat the process for the light harness for the passenger side
    • Move back 18 inches on the wire
    • Cut a foot of the insulation off toward the body of the car
    • Pull the rubber body off the body harness
    • Pull the harnesses out with a flat blade screwdriver
    • Feed the folding and light harness through the body harness boot
    • Place the wires on the corner of the harness connection
    • Slide the harness back into the body
  6. step : Installing the Mirror Wiring Harnesses (8:14)
    • Feed a straightened out coat hanger or stiff wire through the boot
    • Pull the wires through the boot
    • Tape the wires to the coat hanger or wire with electrical tape
    • Feed the wires and coat hanger carefully back through the boot
    • Feed the wires into the door and out through the top hole without interfering with the window regulator
    • Feed the wires through the door and into the mirror pad
    • Hook the wire harnesses into the mirrors
  7. step : Installing the Folding Tow Mirror (10:17)
    • Put the mirror into place
    • Insert and the three 10mm nuts to the mirror
    • Tighten the 10mm nuts
    • Remove the end of the all black wire
    • Loosen the 10mm bolt below the mirror
    • Wrap the ground wire around the bolt
    • Tighten the 10mm bolt
  8. step : Installing the Protective Rubber Boot (11:01)
    • Pull the rubber boot into place and back through the door
    • Reconnect the harnesses
    • Pull the wires through on the other side
    • Snap in the body harness
    • Wire-tie the light and folding wires to prevent movement
    • Push on the water shield
  9. step : Installing the Mirror Wiring Harnesses (11:41)
    • Sustain the harnesses together on the passenger side with electrical tape
    • Wire-tie the harnesses up into the lower panel to prevent them from hanging
    • Wiretap the power fold harness to a switched power source
    • Probe the orange line with an electrical connector
    • Hook the puddle light wiretaps to the blue and green striped wire that ran the dome lights
    • Connect the dome light harness
    • Test the puddle lights
    • Push in the pillar trim
    • Tighten the screw with a 4mm Allen wrench
    • Ground the fold switch to a screw at the bottom of the dash
  10. step : Installing the Mirror Switch (13:30)
    • Drill out a hole in a small panel with a dremel to fit the mirror switch
    • After running the harnesses through both doors connect the switch to the wiring harness
    • Turn the vehicle on
    • Test the power folding switch
    • Turn the vehicle off
    • Disconnect the wiring harness in the engine compartment to create more room
    • Place a piece of stiff wire up through the harness boot
    • Hook the stiff wire onto the power source wire
    • Pull the wire back into the vehicle
    • Open the fuse box
    • Remove the parking light fuse
    • Hook the power source fuse to the parking light fuse
    • Push in the parking light fuse
    • Push the fuse box cover down
    • Reconnect the wiring harness
    • Hook the driver side marker light to the power wire ran from the fuse box with a wiretap
    • Turn the vehicle on
    • Test the marker light
    • Turn the vehicle off
    • Wire-tie the excess wires up into place underneath the dash panel
  11. step : Installing the Lower Dash Panel (16:35)
    • Push the lower dash panel into place
    • Insert and install the lower Phillips head screws
    • Connect the power mirror switch harness
    • Press the power mirror switch into the dash panel
    • Push in the side panel
    • Push in the door soleplate
    • Push in the glovebox
  12. step : Installing the Door Panel (17:18)
    • Reconnect the mirror harness
    • Put the speaker into place
    • Insert the four Phillips screws into the speaker
    • Connect the speaker wiring lead
    • Lift the door panel into place
    • Push in the door panel clips
    • Push in the lock bezel
    • Insert and tighten the two Phillips head screws on the bottom of the door panel
    • Insert and tighten the Phillips head screw at the front top corner of the door panel
    • Insert and tighten the Phillips head screw inside the door handle

Tools needed for replacement:

    Allen Wrenches

  • 4mm Allen Wrench

  • Drills, Drill Bits & Related

  • Drill

  • General Tools

  • Assistant

  • Materials, Fluids, and Supplies

  • Coat Hanger
  • Wire Ties
  • Electrical Tape

  • Pliers, Cutters & misc Wrenches

  • Slip-Joint Pliers
  • Wire Cutters

  • Ratchets & Related

  • Ratchet

  • Screwdrivers & Related

  • Phillips Head Screwdriver
  • Flat Blade Screwdriver

  • Sockets - Metric

  • 10mm Socket

4.00/ 5.0
7 reviews
5 Stars
4 Stars
3 Stars
2 Stars
1 Star
4
1
1
0
1
Fair price. Product fit as stated. The site video on how to replace the mirror was very helpful and led to my ordering from A-1
January 26, 2017
Very Pleased
The mirror came well packaged and on time. It was OEM as described and installed perfectly.
March 3, 2017
I go through A-1 Because they always have what I need
August 10, 2017
Dodge 2008 ram 1500 pasenger mirror
I gave 3 stars because they did try to get me correct mirror twice but thier mirrors for the passenger side are not "objects in mirror are closer than they appear". it is a straight mirror which causes you blind spot to be even bigger. I had to return then and ask for my money back
August 29, 2017
percect fit, some vibration.
The mirror fit and connected perfectly. No loose or misaligned bracketry and the plastic matches seemlessly. The housing does not vibrate but the mirror itself has some vibration in it when driving. Definitely noticeable compared the the original mirror but not enough to totally obstruct view but enough that you have to concentrate to make sure you see everything in the field.
May 30, 2018
easy as pie
this replacement mirror was a perfect match at a great price. I got it super fast and installed it even faster, like nothing ever happened! thanks!
October 2, 2018
Not for On-Road Applications
This mirror is NOT an OEM replacement part! This is a flat mirror that gives an EXTREMELY narrow field of view. I didnt notice that the mirror did not say "OBJECTS IN MIRROR MAY BE CLOSER THAN THEY APPEAR" prior to installing. In use, it looked as though I was looking a paper towel core. I was turning my head around driving on the interstate looking at my blind spot as if I was a beginner driver.
December 26, 2018
Will this fit my car? Add a vehicle to make sure
Customer Q&A
Ask a question to 1A Auto customers who purchased the product
No questions have been asked about this item.
Year Make Model Description
2005-2008Dodge Ram 1500 Truck Dodge Ram 1500 Truck Power Heated Textured Black Mirror Passenger Side
2005-2009Dodge Ram 2500 Truck Dodge Ram 2500 Truck Power Heated Textured Black Mirror Passenger Side
2005-2009Dodge Ram 3500 Truck Dodge Ram 3500 Truck Power Heated Textured Black Mirror Passenger Side
Part #: 1AMRE01830


Order must be placed by 4pm ET
Delivery options for:

Estimated Arrival Cost


Deliveries made to PO Boxes and FPO may take longer. See our Shipping & Delivery for more information.

Get it in: 2 - 4 Business Days

Want it sooner? Choose Next Day Air at Checkout

How-to Video:

(18:55 min)