Replaces

Dodge Mirror - 1AMRE01026

Description
Warranty & Shipping
How-To & Tools
Product Reviews
Q&A
Vehicle Fit

Part Details

  • Mirror Operation:   Manual

This replacement Dodge Pickup mirror is just what you need to get your vehicle in good looking form again!

This mirror features the following specifications:

  • LH Driver's
  • Manual Mirror
  • Sail mount design - Mounts in the corner of the door
  • Injection molded black plastic housing
  • Direct replacement Mirror
  • Built to strict quality control standards

This mirror makes a great replacement and has substantial cost savings over a dealer unit.

Item Condition: New

Attention California Customers:

WARNING:  This product can expose you to chemicals including Lead and Lead Compounds, which are known to the State of California to cause cancer, and birth defects or other reproductive harm.  For more information, go to www.P65Warnings.ca.gov.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

  1. step : Removing the Door Panel (1:06)
    • Remove the Phillips head screw inside the door handle
    • Remove the Phillips head screw at the front top corner of the door panel
    • Remove the two Phillips head screws on the bottom of the door panel
    • Lift the door panel up and off
    • Pop the lock bezel out
    • Pry up the window switch panel by hand
    • Disconnect the window switch wiring harnesses
    • Remove the four Phillips screws from the speaker
    • Pry off the speaker
    • Disconnect the speaker wiring lead
  2. step : Removing the Side Mirror (2:34)
    • Disconnect the mirror wiring harness
    • Remove the three 10mm nuts from the mirror
    • Have an assistant hold the mirror
    • Push in the clips on either side of the harness connection
    • Remove the mirror
  3. step : Removing the Protective Rubber Boot (3:18)
    • Pry up the door soleplate with a flat blade screwdriver
    • Pull the glove box down
    • Push in the tabs on either side of the glove box
    • Pull the glove box down and remove it from the hinge
    • Push in on the tabs on the body harness
    • Pry out and remove the body harness
    • Disconnect the wiring harness
    • Push the rubber boot through the door to release the harness
    • Carefully peel the top left corner of the water shield
  4. step : Removing the Dash Panel (4:58)
    • Remove the side dash panel by hand
    • Remove the screw from the pillar trim with a 4mm Allen wrench
    • Remove the pillar trim
    • Disconnect the dome harness
    • Remove the two Phillips screws from the lower dash panel
    • Pull out on the lower dash panel
  5. step : Installing the Power Fold and Light Wiring Harness (5:51)
    • Run one of the power fold harnesses behind the center and across to the passenger side
    • Feed the wire up through the dash and through the hole on the body
    • Repeat the process for the light harness for the passenger side
    • Move back 18 inches on the wire
    • Cut a foot of the insulation off toward the body of the car
    • Pull the rubber body off the body harness
    • Pull the harnesses out with a flat blade screwdriver
    • Feed the folding and light harness through the body harness boot
    • Place the wires on the corner of the harness connection
    • Slide the harness back into the body
  6. step : Installing the Mirror Wiring Harnesses (8:14)
    • Feed a straightened out coat hanger or stiff wire through the boot
    • Pull the wires through the boot
    • Tape the wires to the coat hanger or wire with electrical tape
    • Feed the wires and coat hanger carefully back through the boot
    • Feed the wires into the door and out through the top hole without interfering with the window regulator
    • Feed the wires through the door and into the mirror pad
    • Hook the wire harnesses into the mirrors
  7. step : Installing the Folding Tow Mirror (10:17)
    • Put the mirror into place
    • Insert and the three 10mm nuts to the mirror
    • Tighten the 10mm nuts
    • Remove the end of the all black wire
    • Loosen the 10mm bolt below the mirror
    • Wrap the ground wire around the bolt
    • Tighten the 10mm bolt
  8. step : Installing the Protective Rubber Boot (11:01)
    • Pull the rubber boot into place and back through the door
    • Reconnect the harnesses
    • Pull the wires through on the other side
    • Snap in the body harness
    • Wire-tie the light and folding wires to prevent movement
    • Push on the water shield
  9. step : Installing the Mirror Wiring Harnesses (11:41)
    • Sustain the harnesses together on the passenger side with electrical tape
    • Wire-tie the harnesses up into the lower panel to prevent them from hanging
    • Wiretap the power fold harness to a switched power source
    • Probe the orange line with an electrical connector
    • Hook the puddle light wiretaps to the blue and green striped wire that ran the dome lights
    • Connect the dome light harness
    • Test the puddle lights
    • Push in the pillar trim
    • Tighten the screw with a 4mm Allen wrench
    • Ground the fold switch to a screw at the bottom of the dash
  10. step : Installing the Mirror Switch (13:30)
    • Drill out a hole in a small panel with a dremel to fit the mirror switch
    • After running the harnesses through both doors connect the switch to the wiring harness
    • Turn the vehicle on
    • Test the power folding switch
    • Turn the vehicle off
    • Disconnect the wiring harness in the engine compartment to create more room
    • Place a piece of stiff wire up through the harness boot
    • Hook the stiff wire onto the power source wire
    • Pull the wire back into the vehicle
    • Open the fuse box
    • Remove the parking light fuse
    • Hook the power source fuse to the parking light fuse
    • Push in the parking light fuse
    • Push the fuse box cover down
    • Reconnect the wiring harness
    • Hook the driver side marker light to the power wire ran from the fuse box with a wiretap
    • Turn the vehicle on
    • Test the marker light
    • Turn the vehicle off
    • Wire-tie the excess wires up into place underneath the dash panel
  11. step : Installing the Lower Dash Panel (16:35)
    • Push the lower dash panel into place
    • Insert and install the lower Phillips head screws
    • Connect the power mirror switch harness
    • Press the power mirror switch into the dash panel
    • Push in the side panel
    • Push in the door soleplate
    • Push in the glovebox
  12. step : Installing the Door Panel (17:18)
    • Reconnect the mirror harness
    • Put the speaker into place
    • Insert the four Phillips screws into the speaker
    • Connect the speaker wiring lead
    • Lift the door panel into place
    • Push in the door panel clips
    • Push in the lock bezel
    • Insert and tighten the two Phillips head screws on the bottom of the door panel
    • Insert and tighten the Phillips head screw at the front top corner of the door panel
    • Insert and tighten the Phillips head screw inside the door handle

Tools needed for replacement:

    Allen Wrenches

  • 4mm Allen Wrench

  • Drills, Drill Bits & Related

  • Drill

  • General Tools

  • Assistant

  • Materials, Fluids, and Supplies

  • Coat Hanger
  • Wire Ties
  • Electrical Tape

  • Pliers, Cutters & misc Wrenches

  • Slip-Joint Pliers
  • Wire Cutters

  • Ratchets & Related

  • Ratchet

  • Screwdrivers & Related

  • Phillips Head Screwdriver
  • Flat Blade Screwdriver

  • Sockets - Metric

  • 10mm Socket

5.00/ 5.0
3 reviews
5 Stars
4 Stars
3 Stars
2 Stars
1 Star
3
0
0
0
0
Review from Anchorage, Alaska
The mirror is a success, Fits like the original! The only complaint is the shipping of $40. When I ordered mirrors a couple years ago - it was FREE shipping, just like the REST of the U.S. states. Once again Alaska is considered a 3rd world country.....
March 15, 2017
side mirror
I w would never have attempted to install this on my own, had it not been for the amazing video from 1AAuto. It made the insulation very easy. The product arrived quickly and was a very high quality.
August 16, 2018
Dodge Ram 2500 Mirror
The part was a perfect fit for my truck. It was easy to install and is of good quality. The price of the mirror is unbeatable and i highly recommend this product.
September 11, 2018
Will this fit my car? Add a vehicle to make sure
Customer Q&A
Ask a question to 1A Auto customers who purchased the product
No questions have been asked about this item.
Year Make Model Description
2002-2008Dodge Ram 1500 Truck Dodge Ram 1500 Truck Manual Mirror Driver Side
2003-2009Dodge Ram 2500 Truck Dodge Ram 2500 Truck Manual Mirror Driver Side
2003-2009Dodge Ram 3500 Truck Dodge Ram 3500 Truck Manual Mirror Driver Side
Part #: 1AMRE01026


Order must be placed by 4pm ET
Delivery options for:

Estimated Arrival Cost


Deliveries made to PO Boxes and FPO may take longer. See our Shipping & Delivery for more information.

Get it in: 2 - 4 Business Days

Want it sooner? Choose Next Day Air at Checkout

How-to Video:

(18:55 min)