Specifications:

  • 4 Piece Kit
    • Fits LH (Driver Side) & RH (Passenger Side) Front & Rear
  • Size:
    • Height - 4-1/2"
    • Extension Width - 3"
  • High quality ABS Plastic
  • Smooth black paint to match finish
  • UV protected from fading and chalking
  • Direct fit, no drilling or cutting required
  • Includes hardware and instructions

Paint To Match Note:

"Paint to match finish" refers to a smooth, paintable surface. This item will be shipped unpainted but will be ready for paint. Final preparation is suggested for better paint coverage and adhesion. 

This part can also be installed without painting if desired. 

Quick, Easy, No-Drill Installation

No permanent modifications required. Flares mount using included wheel arch clips and heavy duty 3M double-sided tape.

Direct Fit

Designed and contoured to fit your specific vehicle.

Durable ABS Plastic

Rugged, impact- and UV-resistant ABS plastic won't crack or warp

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

1ABFK00050
  1. step : Preparing the Extension Style Fender Flares (0:53)
    • Remove the 3M tape as you press the seal into the flare
    • Cut the seal when you reach the end of the flare
    • Turn the wheel out of the wheel well
    • Insert the fender flare into place and find where the bolts align with the flare
    • If your Hemi badge is in the way, go to step 2
    • Remove the Phillips screws/8mm bolts from the wheel well
    • If you have a rusty wheel arch, go to step 4
  2. step : Removing the Hemi Badge (2:00)
    • Mark the fender's position with a piece of tape
    • Heat up the adhesive on the badge with a heat gun, hair dryer, or let it sit in the sun
    • Pry the badge off with a flat blade screwdriver wrapped in tape
    • Scrape off the adhesive with a rubber razor blade, plastic putty knife, or your thumb
    • Wipe the surface with an adhesive remover
    • Adding a thin layer of wax can help remove scrapes and blend the area
    • Return to step 1
  3. step : Installing the Rugged Style Fender Flare (4:00)
    • Place double-sided body molding tape on the back of the badge
    • Cut the ends and carve the badge to fit with the tape
    • Remove the backing and adhere the badge to the vehicle in a higher position
    • Insert the fender flare into place
    • Loosely tighten the bottom screw to the fender flare
    • Align the flare with the body line
    • Tighten the rest of the hardware into the wheel well and flare
    • If necessary, use the self-tapping screws and clips to tighten the flare into place
    • Repeat the process on the other side
  4. step : Removing the Scaling and Bubbling Paint (7:00)
    • This step is only necessary for trucks with rust on the wheel arch
    • Score around the perimeter of the rust/paint bubbles with a razor blade
    • Scrape off any scaling with a flat blade screwdriver
    • Sand down the area
    • Treat the body with rust-preventative coating or paint
    • When finished, go to step 3

Tools needed for replacement:

    General Tools

  • Putty Knife
  • Utility Knife
  • Heat Gun

  • Materials, Fluids, and Supplies

  • Hair Dryer
  • Sandpaper
  • Double-Sided Tape

  • Ratchets & Related

  • Ratchet

  • Screwdrivers & Related

  • Phillips Head Screwdriver
  • Flat Blade Screwdriver

  • Sockets - Metric

  • 8mm Socket

5.0 / 5.0
1 Review
5 Stars
4 Stars
3 Stars
2 Stars
1 Stars
1
0
0
0
0
Fender flares
Exact fit, great video very very pleased. I always wish the price could be lower but all in all I am satisfied. I provided my own hardware I had beefier screws.
August 8, 2017
Purchased
11 months ago
Start typing your question and we'll check if it was already asked and answered. Learn More
Browse 1 question Browse 1 question and 2 answers
Have mud flaps on my Dodge Ram 1500 can I still use fender flares on it?
Robert on Jan 8, 2017
BEST ANSWER: Hello Robert. If you wish to install these fender flares you will have to sacrifice the mudflaps, unfortunately. This is due to the flares using the existing mounting holes of the mudflaps.

Vehicle Fit

  • 2002-2008 Dodge Ram 1500 Truck Smooth - Paint to Match Black Extension Style Fender Flare Kit 4 Piece Set
  • 2003-2009 Dodge Ram 2500 Truck Smooth - Paint to Match Black Extension Style Fender Flare Kit 4 Piece Set
  • 2003-2009 Dodge Ram 3500 Truck with Single Rear Wheels (SRW) Smooth - Paint to Match Black Extension Style Fender Flare Kit 4 Piece Set
Part #: 1ABFK00050


How-to Video:

(10:44 min)