Replaces

Dodge Dakota Durango Wheel Bearing & Hub Assembly TRQ BHA86535 - 1ASHS01223

 

Precision Engineered

Precision Engineered using the highest grade SAE 1055 / 65Mn high carbon steel to exact OEM design.

100% Factory tested to precise OEM tolerances.

Highest Quality Materials

High quality, multi-lip seal reduces the intrusion of dirt and water, keeping grease clean for a longer bearing life.

Premium, heavy duty grease resists high temperature, moisture, and reduces intense friction pressure to help extend the life of the bearing.

Direct Fit Replacement

Direct fit replacement part is guaranteed to fit and function correctly for your specific application

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

  1. step : Removing the Wheel (1:10)
    • While your car is still on the ground, use your 32mm socket to loosen the center hub nut
    • Loosen your lug nuts and jack up the car
    • Remove the lug nuts with your 19mm socket and ratchet
    • Remove the wheel and set aside
  2. step : Removing the Brakes (1:20)
    • Remove the T47 torx bolts holding the calipers and the bracket
    • Wire tie the caliper up and out of the way, set the bracket to the side
    • Remove your rotor and set aside
  3. step : Removing the Axle (1:56)
    • Remove the 14mm bolts securing the axle
    • Use an axle puller or a light, but firm, tap with a small hammer on the axle to remove it
  4. step : Remving the Hub (5:30)
    • Remove the three 22 mm bolts, using penetrating oil to help
    • A breaker bar or piece of pipe on the end of your ratchet may be needed
    • Remove the hub and clean the area with a wire brush
  5. step : Replacing the Hub (7:20)
    • Clean hub seating with a wire brush and add a little anti-seize grease
    • Put position your new 1A Auto hub in its seating
    • Put the three 22 mm bolts in place and tighten the nuts to 90 ft lbs
    • Reinstall the axle and torque the 14 mm bolts to 60 ft lbs
  6. step : Reinstalling the Brakes and Wheel (8:45)
    • Refer to our other videos for more detailed instructions
    • Remember to replace the lug nuts on in a star pattern
    • Lug nuts tighten to 90-100 ft lbs
    • Hub nut is 175 ft lbs
    • Make sure to check your brakes and steering before driving again
    • Make sure to have the vehicle aligned

Tools needed for replacement:

    General Tools

  • Floor Jack
  • Jack Stands
  • Large C-Clamp
  • Wire Brush

  • Materials, Fluids, and Supplies

  • Anti-Seize Grease
  • Wire Ties

  • Pliers, Cutters & misc Wrenches

  • Needle nose pliers

  • Ratchets & Related

  • Ratchet

  • Screwdrivers & Related

  • Flat Blade Screwdriver

  • Sockets - Metric

  • 14mm Socket
  • 18mm Socket
  • 19mm Socket
  • 32mm Socket

  • Torx Drivers & Sockets

  • T47 Torx Socket

There are no reviews for this item. Write Review
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

  • 1997-2004 Dodge Dakota 4 Wheel Drive Front Wheel Bearing & Hub Assembly for Models with 4 Wheel ABS Brakes Driver Side with (1) 32mm Axle Nut Socket TRQ
  • 1998-2003 Dodge Durango 4 Wheel Drive Front Wheel Bearing & Hub Assembly for Models with 4 Wheel ABS Brakes Driver Side with (1) 32mm Axle Nut Socket TRQ

This part replaces:

  • TRQ BHA86535
Part #: 1ASHS01223


TRQ
Brand #: BHA86535

How-to Video:

(12:36 min)