Replaces

Dodge Dakota Durango Wheel Bearing & Hub Assembly Front Timken HA599528 - TKSHF00124

Description
Warranty & Shipping
How-To & Tools
Product Reviews
Q&A
Vehicle Fit

Part Details

  • Front or Rear Location:   Front

TIMKEN WHEEL BEARING & HUB ASSEMBLY: HA599528

This replacement hub & bearing assembly is just what you need to get your vehicle in good working order again.

Specifications:

  • Brand New Timken Wheel Bearing & Hub Assembly
  • Fits either LH (Driver Side) or RH (Passenger Side) FRONT
  • Fits 6 Lug Wheel
  • Replaces dealer part number: 52009528
  • Direct replacement
  • Built to strict quality control standards
  • New wheel studs installed
  • Fits 2WD (Two Wheel Drive) Models only
  • Fits models with RWAL (Rear Wheel ABS) only

Note:
These parts are authentic Timken brand products that are supplied and packaged by Timken.   In some cases, Timken will source parts from other high quality suppliers such as SKF and Koyo. These parts are subjected to the very same testing and quality standards as all Timken products.

Item Condition: New

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

  1. step : Removing the Wheel (1:10)
    • While your car is still on the ground, use your 32mm socket to loosen the center hub nut
    • Loosen your lug nuts and jack up the car
    • Remove the lug nuts with your 19mm socket and ratchet
    • Remove the wheel and set aside
  2. step : Removing the Brakes (1:20)
    • Remove the T47 torx bolts holding the calipers and the bracket
    • Wire tie the caliper up and out of the way, set the bracket to the side
    • Remove your rotor and set aside
  3. step : Removing the Axle (1:56)
    • Remove the 14mm bolts securing the axle
    • Use an axle puller or a light, but firm, tap with a small hammer on the axle to remove it
  4. step : Remving the Hub (5:30)
    • Remove the three 22 mm bolts, using penetrating oil to help
    • A breaker bar or piece of pipe on the end of your ratchet may be needed
    • Remove the hub and clean the area with a wire brush
  5. step : Replacing the Hub (7:20)
    • Clean hub seating with a wire brush and add a little anti-seize grease
    • Put position your new 1A Auto hub in its seating
    • Put the three 22 mm bolts in place and tighten the nuts to 90 ft lbs
    • Reinstall the axle and torque the 14 mm bolts to 60 ft lbs
  6. step : Reinstalling the Brakes and Wheel (8:45)
    • Refer to our other videos for more detailed instructions
    • Remember to replace the lug nuts on in a star pattern
    • Lug nuts tighten to 90-100 ft lbs
    • Hub nut is 175 ft lbs
    • Make sure to check your brakes and steering before driving again
    • Make sure to have the vehicle aligned

Tools needed for replacement:

    General Tools

  • Floor Jack
  • Jack Stands
  • Large C-Clamp
  • Wire Brush

  • Materials, Fluids, and Supplies

  • Anti-Seize Grease
  • Wire Ties

  • Pliers, Cutters & misc Wrenches

  • Needle nose pliers

  • Ratchets & Related

  • Ratchet

  • Screwdrivers & Related

  • Flat Blade Screwdriver

  • Sockets - Metric

  • 14mm Socket
  • 18mm Socket
  • 19mm Socket
  • 32mm Socket

  • Torx Drivers & Sockets

  • T47 Torx Socket

There are no reviews for this item.
Will this fit my car? Add a vehicle to make sure
Customer Q&A
Ask a question to 1A Auto customers who purchased the product
No questions have been asked about this item.
Year Make Model Description
1997-2004Dodge Dakota Dodge Dakota Rear Wheel Drive Front Wheel Bearing & Hub Assembly for Models with Rear Wheel ABS Brakes Timken HA599528
1999-2003Dodge Durango Dodge Durango Rear Wheel Drive Front Wheel Bearing & Hub Assembly for Models with Rear Wheel ABS Brakes Timken HA599528
Only 4 left in stock
Part #: TKSHF00124


Order must be placed by 4pm ET

Get it in: 2 - 4 Business Days

Want it sooner? Choose Next Day Air at Checkout

Timken
Brand #: HA599528

How-to Video:

(12:36 min)