Replaces

Dodge Dakota Durango Wheel Bearing & Hub Assembly Front Pair TRQ BHA53383 - 1ASHS00105

Part Details

  • Wheel Bearing & Hub Assembly Features & Benefits:
    Direct Fit Replacement
    Precision Engineered
    Highest Quality Materials
  • Bearing Type: Tapered Roller Bearing
  • Quantity: Pair
  • Front or Rear Location: Front

Specifications:

  • Comes as a PAIR
    • Fits both LH (Driver Side) & RH (Passenger Side) FRONT
  • Fit 6 Lug Wheels
  • Replaces dealer part numbers: 52009406, 52009406AB, 52009406AC, 52009406AD, 52009406AE
  • New wheel studs installed
  • Direct replacements
  • Built to strict quality control standards
  • Fit 2WD (Two Wheel Drive) Models only
  • Fit models with AWAL (4 Wheel Anti-Lock Brakes) only

What are Tapered Bearings and Why Use Them?

Tapered bearings are better than roller ball bearings at handling forces exerted on the bearing during cornering (known as axial load) in trucks and large cars. 

Roller ball bearings have spherical ball bearings between two straight rings (called races). Tapered bearings use tapered rollers shaped like flat-topped cones and two races angled from the outside to the inside of the bearing. The greater the angle, the more axial load the bearing can handle.

Your model came from the factory with tapered bearings. This type of bearing handles cornering forces better for trucks and large cars. Roller ball bearings work well for smaller cars, but replacing a tapered bearing with a roller ball bearing will result in increased wear and faster failure.

 

Item Condition: New

WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

BHA53956 Axle / Spindle Nut Torque Specification

  1. step : Removing the Wheel (1:10)
    • While your car is still on the ground, use your 32mm socket to loosen the center hub nut
    • Loosen your lug nuts and jack up the car
    • Remove the lug nuts with your 19mm socket and ratchet
    • Remove the wheel and set aside
  2. step : Removing the Brakes (1:20)
    • Remove the T47 torx bolts holding the calipers and the bracket
    • Wire tie the caliper up and out of the way, set the bracket to the side
    • Remove your rotor and set aside
  3. step : Removing the Axle (1:56)
    • Remove the 14mm bolts securing the axle
    • Use an axle puller or a light, but firm, tap with a small hammer on the axle to remove it
  4. step : Remving the Hub (5:30)
    • Remove the three 22 mm bolts, using penetrating oil to help
    • A breaker bar or piece of pipe on the end of your ratchet may be needed
    • Remove the hub and clean the area with a wire brush
  5. step : Replacing the Hub (7:20)
    • Clean hub seating with a wire brush and add a little anti-seize grease
    • Put position your new 1A Auto hub in its seating
    • Put the three 22 mm bolts in place and tighten the nuts to 90 ft lbs
    • Reinstall the axle and torque the 14 mm bolts to 60 ft lbs
  6. step : Reinstalling the Brakes and Wheel (8:45)
    • Refer to our other videos for more detailed instructions
    • Remember to replace the lug nuts on in a star pattern
    • Lug nuts tighten to 90-100 ft lbs
    • Hub nut is 175 ft lbs
    • Make sure to check your brakes and steering before driving again
    • Make sure to have the vehicle aligned

Tools needed for replacement:

    General Tools

  • Floor Jack
  • Jack Stands
  • Large C-Clamp
  • Wire Brush

  • Materials, Fluids, and Supplies

  • Anti-Seize Grease
  • Wire Ties

  • Pliers, Cutters & misc Wrenches

  • Needle nose pliers

  • Ratchets & Related

  • Ratchet

  • Screwdrivers & Related

  • Flat Blade Screwdriver

  • Sockets - Metric

  • 14mm Socket
  • 18mm Socket
  • 19mm Socket
  • 32mm Socket

  • Torx Drivers & Sockets

  • T47 Torx Socket

5.0 / 5.0
1 Review
5 Stars
4 Stars
3 Stars
2 Stars
1 Star
1
0
0
0
0
Perfect fit, easy to install
These were a perfect fit for my 2003 Dodge Durango. The items shipped and were delivered on time. Installation was easy and the bearings are functioning perfectly.
February 21, 2017
Purchased
1 year ago
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

Year Make Model Description
1997-2004Dodge Dakota Dodge Dakota Rear Wheel Drive Front Wheel Bearing & Hub Assembly for Models with 4 Wheel ABS Brakes Pair TRQ
1998-2003Dodge Durango Dodge Durango Rear Wheel Drive Front Wheel Bearing & Hub Assembly for Models with 4 Wheel ABS Brakes Pair TRQ

This part replaces:

  • TRQ BHA53383
Part #: 1ASHS00105


Order must be placed by 4pm ET

Get it in: 2 - 4 Business Days

Want it sooner? Choose Next Day Air at Checkout

TRQ
Brand #: BHA53383

How-to Video:

(12:36 min)