This inner tie rod assembly is just what you need to ensure the safety and integrity of your vehicle's suspension and steering.

Specifications:

  • Fits either the LH (Driver Side) or RH (Passenger Side) FRONT INNER
  • Replaces dealer part numbers: 52106405AC, 52106405AI, 52106405AJ
  • Direct replacement
  • Built to strict quality control standards
  • Fits 4WD (Four Wheel Drive) Models only

Remember whenever you are replacing any front end or steering components you should have your vehicle professionally aligned as soon as possible. This will ensure proper tracking and even tire wear.

Our steering and suspension components are sealed for long life and do not require the extra maintenance typically required by greasable versions.

Please Note: Whenever replacing steering components, it is highly recommended to have a professional alignment performed on the vehicle afterwards.  Failure to do so may result in issues with steering and premature tire wear.

Part Details

  • Location: Inner
  • Front or Rear Location: Front

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

  1. step : Removing the Wheel (0:38)
    • Loosen the 22mm lug nuts with the vehicle on the ground
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the lug nuts
    • Pull off the wheel
  2. step : Removing the Outer Tie Rod (1:49)
    • Loosen the 24mm nut that holds the outer tie rod to the inner tie rod with an adjustable wrench
    • Remove the 22mm nut from the outer tie rod end
    • Strike the steering knuckle with a hammer to loosen the outer tie rod
    • Pull the outer tie rod out of the steering knuckle
    • Twist off the outer tie rod by hand
  3. step : Installing the New Outer Tie Rod (3:49)
    • Twist the new outer tie rod onto the inner tie rod
    • Push the outer tie rod into the steering knuckle
    • Fasten the 22mm castle nut onto the outer tie rod
    • Torque the nut to 45 foot-pounds, then torque to an additional 90 degrees
    • Push the cotter pin through the castle nut
    • Twist the cotter pin into place with needle nose pliers
    • Tighten the 24mm nut that holds the outer tie rod to the inner tie rod with an adjustable wrench
  4. step : Reattaching the Wheel (5:08)
    • Slide the wheel into place
    • Start the 22mm lug nuts by hand
    • Tighten the lug nuts preliminarily
    • Lower the vehicle to the ground
    • Tighten the lug nuts to between 135 foot-pounds in a crossing or star pattern

Tools needed for replacement:

    General Tools

  • Jack Stands
  • Floor Jack

  • Ratchets & Related

  • Ratchet
  • Torque Wrench
  • Socket Extensions
  • 1/2 Inch Breaker Bar

  • Sockets - Metric

  • 22mm Socket

  • Wrenches - Metric

  • 24mm Wrench

There are no reviews for this item. Write Review
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

Year Make Model Description
2000-2004Dodge Dakota Dodge Dakota 4 Wheel Drive Front Inner Tie Rod Driver or Passenger Side
2000-2003Dodge Durango Dodge Durango 4 Wheel Drive Front Inner Tie Rod Driver or Passenger Side

This part replaces:

  • OE # 52106405AC, 52106405AI, 52106405AJ
  • Moog EV432
Part #: 1ASTE00278


Order must be placed by 4pm ET

Get it in: 2 - 4 Business Days

Want it sooner? Choose Next Day Air at Checkout

How-to Video:

(06:11 min)