Replaces

Dodge Dakota Durango Steering & Suspension Kit - 1ASFK05791

Our steering and suspension components come pre-greased, sealed for long life, and do not require the extra maintenance typically required by greasable versions.

Please Note: Whenever replacing steering components, it is highly recommended to have a professional alignment performed on the vehicle afterwards.  Failure to do so may result in issues with steering and premature tire wear.

Direct Fit

All parts are direct fit, application-specific parts with no modifications required

Rigorously Tested

Rigorously tested and made from higher quality materials than the competition. Our parts are built to have a longer life in any environment or road conditions.

State of the Art Manufacturing

Our parts are manufactured by some of the same factories that the OEMs use.

Prepackaged for Your Convenience

Our kits have been carefully put together to include all of the parts you need to get the job done, saving you both time and money. These kits also help take the guesswork out of finding the correct part for your vehicle’s steering or suspension system, allowing you to get started on your repair project faster.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

  1. step : Removing the Wheel (0:38)
    • Loosen the 22mm lug nuts with the vehicle on the ground
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the lug nuts
    • Pull off the wheel
  2. step : Removing the Outer Tie Rod (1:49)
    • Loosen the 24mm nut that holds the outer tie rod to the inner tie rod with an adjustable wrench
    • Remove the 22mm nut from the outer tie rod end
    • Strike the steering knuckle with a hammer to loosen the outer tie rod
    • Pull the outer tie rod out of the steering knuckle
    • Twist off the outer tie rod by hand
  3. step : Installing the New Outer Tie Rod (3:49)
    • Twist the new outer tie rod onto the inner tie rod
    • Push the outer tie rod into the steering knuckle
    • Fasten the 22mm castle nut onto the outer tie rod
    • Torque the nut to 45 foot-pounds, then torque to an additional 90 degrees
    • Push the cotter pin through the castle nut
    • Twist the cotter pin into place with needle nose pliers
    • Tighten the 24mm nut that holds the outer tie rod to the inner tie rod with an adjustable wrench
  4. step : Reattaching the Wheel (5:08)
    • Slide the wheel into place
    • Start the 22mm lug nuts by hand
    • Tighten the lug nuts preliminarily
    • Lower the vehicle to the ground
    • Tighten the lug nuts to between 135 foot-pounds in a crossing or star pattern

Tools needed for replacement:

    General Tools

  • Jack Stands
  • Floor Jack

  • Ratchets & Related

  • Ratchet
  • Torque Wrench
  • Socket Extensions
  • 1/2 Inch Breaker Bar

  • Sockets - Metric

  • 22mm Socket

  • Wrenches - Metric

  • 24mm Wrench

There are no reviews for this item. Write Review
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

  • 2000-2004 Dodge Dakota 4 Wheel Drive Steering & Suspension Kit 10 Piece Set
  • 2000-2003 Dodge Durango 4 Wheel Drive Steering & Suspension Kit 10 Piece Set

This part replaces:

  • OE # 52106222AA
  • OE # 52106386
  • OE # 52106387
  • OE # 52106405AC
  • OE # 52106405AI
  • OE # 52106405AJ
  • OE # 52106544AA
  • OE # 52106544AD
  • OE # 52106545AA
  • OE # 52106545AD
  • Dorman 520-309
  • Dorman 520-310
  • Moog ES3572
  • Moog ES3573
  • Moog EV432
  • Moog K7395
Part #: 1ASFK05791


How-to Video:

(06:11 min)