Replaces

Dodge Dakota Durango Steering & Suspension Kit - 1ASFK01084

Specifications:

  • Brand New Suspension Kit
  • Fits LH (Driver Side) & RH (Passenger Side) Front
  • Built to strict quality control standards
  • Direct replacements

Our steering and suspension components come pre-greased, sealed for long life, and do not require the extra maintenance typically required by greasable versions.

Please Note: Whenever replacing steering components, it is highly recommended to have a professional alignment performed on the vehicle afterwards.  Failure to do so may result in issues with steering and premature tire wear.

Direct Fit

All parts are direct fit, application-specific parts with no modifications required

Rigorously Tested

Rigorously tested and made from higher quality materials than the competition. Our parts are built to have a longer life in any environment or road conditions.

State of the Art Manufacturing

Our parts are manufactured by some of the same factories that the OEMs use.

Prepackaged for Your Convenience

Our kits have been carefully put together to include all of the parts you need to get the job done, saving you both time and money. These kits also help take the guesswork out of finding the correct part for your vehicle’s steering or suspension system, allowing you to get started on your repair project faster.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

  1. step : Removing the Wheel (0:47)
    • Loosen the lug nuts
    • Raise and support the vehicle
    • Remove the lug nuts
    • Pull off the wheel
  2. step : Removing the Outer Tie Rod (1:14)
    • Soak the tie rod jam nut and the other tie rod nut in rust penetrant
    • Loosen the jam nut with a 24mm wrench
    • Remove the 21mm nut from the outer tie rod
    • Strike the wheel spindle with a hammer to release the outer tie rod
    • Pull the tie rod down out of the wheel spindle
    • Twist off the tie rod, counting how many turns it takes to remove
    • Hold the inner tie rod with locking pliers
    • Mark the jam nut position with a marker
    • Twist off the jam nut with a 24mm wrench, counting how many turns it takes to remove
  3. step : Installing the Outer Tie Rod (5:25)
    • Mark the new jam nut
    • Twist on the new jam nut the same number of turns it took to remove the old one
    • Twist on the outer tie rod the same number of turns it took to remove the old one
    • Insert the outer tie rod stud into the wheel spindle
    • Fasten the 22mm nut onto the outer tie rod
    • Tighten the 22mm nut to 63 foot-pounds of torque
    • Tighten the new jam nut with a 22mm wrench
    • Grease the tie rod fitting until the boot swells
  4. step : Installing the Wheel (7:04)
    • Lift the wheel into place
    • Start the lug nuts
    • Lower the vehicle to the ground
    • Tighten the lug nuts to 110 foot-pounds

Tools needed for replacement:

    General Tools

  • Jack Stands
  • Hammer
  • Floor Jack

  • Materials, Fluids, and Supplies

  • Gloves
  • Rust Penetrant
  • Marker / Writing Utensil

  • Pliers, Cutters & misc Wrenches

  • Vise Grip Pliers
  • Side Cutters

  • Ratchets & Related

  • Ratchet
  • Torque Wrench
  • Socket Extensions
  • 1/2 Inch Breaker Bar

  • Sockets - Metric

  • Complete Metric Socket Set

4.3 / 5.0
3 Reviews
5 Stars
4 Stars
3 Stars
2 Stars
1 Stars
1
2
0
0
0
Parts review
I ordered my front end kit. It was easily installed. My truck now is running really good. No squeaking no banging no see sawing. The ordering and the shipping process was very quick as well. Will do business with this company again when needed.
May 14, 2018
Purchased
1 month ago
Fits good
Product seems strong and fits perfect we will see how long it withstands offroading. Shipping coul have been a little faster but I got it on day 5.
February 8, 2018
Purchased
4 months ago
Dakota front suspension kit
Parts fit well, and have grease fittings which is a plus over the stock parts. The only quality I see that should be improved is the location of the grease fitting for the sway bar links. The driver side fitting has zero clearance and and broke off when I moved the truck. The pass side fitting clears the mounting bracket with almost no room .to add grease in the future. I suggest adding grease before installing the sway bar links. All other parts fit fine, now lets see how long they last.
January 23, 2017
Purchased
1 year ago
Start typing your question and we'll check if it was already asked and answered. Learn More
Browse 1 question Browse 1 question and 3 answers
Are these ball joints serviceable?
Carter R on Jun 29, 2016
BEST ANSWER: Lower BJ YES, Upper BJ NO

Vehicle Fit

  • 2000-2004 Dodge Dakota 2 Wheel Drive 10 Piece Set Steering & Suspension Kit
  • 2000-2003 Dodge Durango 2 Wheel Drive 10 Piece Set Steering & Suspension Kit

This part replaces:

  • Moog K7392
  • Moog ES3571
  • Moog K7393
  • Moog K7274
  • Moog EV406
  • OE # 52013468AC, 52106710AC
  • OE # 5104788AB
Part #: 1ASFK01084


How-to Video:

(07:32 min)