Dodge Charger Magnum Chrysler 300 Heater Blower Motor with Fan Cage - 1AHCX00230

Frequently bought together

Warranty & Shipping
How-To & Tools
Product Reviews
Vehicle Fit

This Chrysler 300, Dodge Magnum, & Charger heater blower motor with fan cage is a new, aftermarket replacement part. It is just what you need to bring your heating and A/C blower system back to good working order! This assembly has the following


  • New, not remanufactured or rebuilt
  • Includes blower motor fan cage impeller already installed
  • Direct replacement
  • Replaces dealer part number: 5061091AB
  • Built to strict quality control standards
  • 100% tested prior to leaving the factory

If you are experiencing intermittent stopping during use, squealing noise from bearings, or poor air flow from your dash vents this may be your solution.

Our electrical and electronic parts are subject to strict quality testing.

Parts cannot be returned after they have been installed. Contact us with any questions before installing the parts.

Left Hand Drive Note:

“All of our auto parts are intended for Left Hand Drive USDM vehicles and might not have been tested on Right Hand Drive platforms. If your vehicle is Right Hand Drive, please do your research prior to making a purchase to ensure the part is correct for your specific vehicle.”

Item Condition: New

Attention California Customers:

WARNING:  This product can expose you to chemicals including Di(2-ethylhexyl)phthalate (DEHP), which is known to the State of California to cause cancer, and birth defects or other reproductive harm.  For more information, go to

Lifetime Warranty

This item is backed by our limited lifetime warranty. In the event this item should fail due to manufacturing defects during intended use, we will replace the part free of charge.

  1. step : Removing the Blower Motor (0:47)
    • Remove the plastic clips from underneath the dash with a trim tool
    • Pull down the carpeted panel under the dash
    • Disconnect the bower motor wiring harness
    • Remove the four 8mm bolts from the blower motor
    • Pull out the blower motor
    • Unclip the wiring harness retainers with a trim tool
  2. step : Installing the Blower Motor (4:26)
    • Clip the wiring harness retainers to the blower motor
    • Put the blower motor into place
    • Install the four 8mm bolts for the blower motor
    • Connect the blower motor wiring harness
    • Put the carpet into place
    • Push the plastic clips into the carpet

Tools needed for replacement:

    Ratchets & Related

  • Ratchet
  • Socket Extensions

  • Screwdrivers & Related

  • Flat Blade Screwdriver

  • Sockets - Metric

  • 8mm Socket

  • Specialty Tools

  • Trim Tool Set

4.50/ 5.0
2 reviews
5 Stars
4 Stars
3 Stars
2 Stars
1 Star
Packing issues
The blower works well and installation was easy . The problem was that when I opened the box I found that one of the tabs used to hold the wiring harness was broken. Luckily I was still able to make the harness work
May 3, 2017
Perfect part
I was leary about buying parts off the internet but 1aauto assured me that it would fit. Not only did it fit, they had installation videos on YouTube. It made my work a lot easier since Im not a mechanic at all. 5 out of 5
February 3, 2019
Will this fit my car? Add a vehicle to make sure
Customer Q&A
Ask a question to 1A Auto customers who purchased the product
No questions have been asked about this item.
Year Make Model Description
2005-2007Chrysler 300 Chrysler 300 Heater Blower Motor with Fan Cage
2006-2007Dodge Charger Dodge Charger Heater Blower Motor with Fan Cage
2005-2007Dodge Magnum Dodge Magnum Heater Blower Motor with Fan Cage
Only 9 left in stock
Part 1AHCX00230
In Stock

Order must be placed by 4pm ET
Delivery options for:

Estimated Arrival Cost

Deliveries made to PO Boxes and FPO may take longer. See our Shipping & Delivery for more information.