This axle shaft is just what you need to get your vehicle in good working order!

Specifications:

  • Fits either the LH (Driver) or RH (Passenger Side) FRONT
  • Replaces dealer part numbers: 5L3Z 3B436 A, 5L3Z3B436A
  • Brand New, not refurbished or rebuilt
  • Built to strict quality control standards
  • No core charge

This cv axle shaft makes a great replacement and has good cost savings over the dealer unit!

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

  1. step : Remove the wheel (1:03)
    • Remove the lug cap
    • Loosen the lug nuts.
    • Remove the cover and cotter pin from the hub nut and loosen the hub nut.
    • Loosen the seven 13 mm 12 point bolts securing the axle to the front drive.
  2. step : Disconnect the stabilizer link (1:55)
    • Hit them with penetrating oil
    • Use a 14 mm socket and 9/16 socket on the bottom to remove the stabilizer link.
    • This might take a bit of elbow grease with hand tools, but it will come loose.
    • Use a hammer to drive out the stabilizer link.
  3. step : Remove the half shaft of the CV axle. (3:38)
    • Use a large crow bar between the lug bolts to secure the axle while you remove the 13 mm 12 point bolts if you didn't loosen them earlier.
    • Remove the hub nut.
    • Give the axle a good tap with the hammer to break it loose from the steering knuckle.
    • Pull the axle out.
  4. step : Install the new half shaft of the CV axle (5:23)
    • Install the grease fitting on the ball joint and fill with grease.
    • Put the new axle in and bolt in.
    • In a star pattern, torque the 13 mm 12 point bolts to 60 ft lbs.
  5. step : Install the new stabilizer link. (6:20)
    • Thread the bushings and washers on the stabilizer bar and tighten the lock nuts down.
    • Jack up the suspension a bit and tighten the stabilizer link up to 15-17 ft lbs.
  6. step : Put your hub and lug nuts and wheel back on. (7:20)
    • Put the hub nut on and pre-tighten but don't torque it.
    • Put the wheel and lug nuts back on
    • Lower the vehicle and torque the lug nuts in a star pattern to 100 ft lbs.
    • Torque the hub nut to 220 ft lbs.
    • Replace the cotter pin and cover on the hub nut.
    • Put the lug cover back on.

Tools needed for replacement:

    General Tools

  • Center Punch
  • Jack Stands
  • Hammer
  • Floor Jack

  • Materials, Fluids, and Supplies

  • Rust Penetrant

  • Ratchets & Related

  • Ratchet
  • Socket Extensions
  • 1/2 Inch Breaker Bar
  • Torque Wrench

  • Screwdrivers & Related

  • Flat Blade Screwdriver

  • Sockets - Metric

  • 13mm Socket
  • 14mm Socket
  • 19mm Socket
  • 35mm Socket

  • Sockets - SAE

  • 9/16 Inch Socket

3.5 / 5.0
2 Reviews
5 Stars
4 Stars
3 Stars
2 Stars
1 Stars
1
0
0
1
0
Ford Expedition cv axle shaft replacemant
Fast shipping, item exactly as described, perfect fit, followed the video instruction from teardown to installation of the new part and job was completed without any problems. Will definitely order more parts and I highly recommend your store.
November 2, 2017
Purchased
4 months ago
CV Axle
The CV axle is working fine, solved a vibration problem I was having at 55 MPH and above. Only time will tell regarding the longevity of this part. The CV Axle I had to replace (O'Reilly Auto) only lasted 40K miles, while the OEM (Ford F-150) axle lasted 240K miles. I hope to get far more than 40K miles on the 1A-Auto axle.

KG
November 5, 2017
Purchased
4 months ago
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

How-to Video:

(08:53 min)

Tools List:

    General Tools

  • Center Punch
  • Jack Stands
  • Hammer
  • Floor Jack

  • Materials, Fluids, and Supplies

  • Rust Penetrant

  • Ratchets & Related

  • Ratchet
  • Socket Extensions
  • 1/2 Inch Breaker Bar
  • Torque Wrench

  • Screwdrivers & Related

  • Flat Blade Screwdriver

  • Sockets - Metric

  • 13mm Socket
  • 14mm Socket
  • 19mm Socket
  • 35mm Socket

  • Sockets - SAE

  • 9/16 Inch Socket



This part replaces:

  • A1 Cardone 66-2112

Vehicle Fit

  • 1997-2002 Ford Expedition Front CV Axle Shaft Driver or Passenger Side
  • 2004 Ford F150 Heritage Truck Front CV Axle Shaft Driver or Passenger Side
  • 1997-2003 Ford F150 Truck Front CV Axle Shaft Driver or Passenger Side
  • 1997-1999 Ford F250 Light Duty Truck Front CV Axle Shaft Driver or Passenger Side
  • 1998-2002 Lincoln Navigator Front CV Axle Shaft Driver or Passenger Side
Part #: 1AACV00147

Ships Same Day for orders placed by 4 P.M. ET

We're here to help

1A Auto Parts

Customer Feedback

"Thanks for the fast reliable service. Great price, and the headlights were as good as oem or better!!! Keep up the good work..."
- Dwuan M.
Read More