Specifications:

  • Brand New Complete CV Driveshaft Assembly
  • Fits LH (Driver Side) FRONT
  • Inboard Splines - 29
  • Outboard Splines - 29
  • Axle Length - 24-15/16"
  • No core charge
  • Direct replacement
  • Built to strict quality control standards

CV axles are designed to transmit the power from your vehicle's drivetrain to the wheels while being able to flex and pivot to the demands of the steering and suspension systems.  If your vehicle is making clicking noises at lower speeds or when making turns, it may be time to replace your CV axles with our 100% brand new assemblies.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

  1. step : Removing the Wheel (1:30)
    • Loosen the lug nuts with the vehicle on the ground
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the lug nuts
    • Pull off the wheel
  2. step : Removing the Axle from the Hub (1:51)
    • Twist the cotter pin out of the axle
    • Remove the 32mm hub nut
    • Make sure the axle moves freely in the hub
    • If the axle is seized, thread the hub nut on, and strike the axle with a hammer to loosen it
  3. step : Pulling Aside the Stabilizer Link (3:05)
    • Hold the lower stabilizer link stud with a 14mm wrench
    • Remove the lower 15mm nut from the stabilizer link
    • Push the stabilizer link out of the lower control arm
  4. step : Pulling Aside the Lower Control Arm (3:57)
    • Remove the six 22mm bolts from the lower control arm
    • Pull the control arm down
  5. step : Removing the Axle Shaft (4:49)
    • Push the axle out of the hub
    • Have a drain pan ready
    • Separate the axle from the transmission with a pry bar
  6. step : Installing the New Axle (5:34)
    • Push the axle into place at the transmission
    • Push the axle into the wheel hub
  7. step : Reinstalling the Control Arm (6:12)
    • Raise the control arm into place
    • Start the six 22mm bolts into the control arm
    • Tighten the 22mm bolts to 120 foot-pounds of torque
  8. step : Reinstalling the Stabilizer Link (7:03)
    • Push the stabilizer link into place
    • Hold the lower stabilizer link stud with a 14mm wrench
    • Fasten the lower 15mm nut onto the stabilizer link
  9. step : Fastening the Axle (7:18)
    • Install the 32mm hub nut
    • Have an assistant press the brake pedal
    • Tighten the hub nut to 217 foot-pounds
    • Insert the cotter pin into the axle
  10. step : Refilling the Transmission Fluid (7:49)
    • Have a drain pan ready
    • Remove the drain plug from the transmission with a 10mm Allen wrench
    • Fill the transmission, using a hose, until fluid begins to drip out
    • Insert the drain plug
  11. step : Reattaching the Wheel (8:27)
    • Slide the wheel into place
    • Start the lug nuts by hand
    • Tighten the lug nuts preliminarily
    • Lower the vehicle to the ground
    • Tighten the lug nuts to 100 foot-pounds in a crossing or star pattern
    • Have your vehicle professionally aligned

Tools needed for replacement:

    Air Powered Tools

  • 1/2 Inch Air Impact Gun

  • Allen Wrenches

  • 10mm Allen Wrench

  • General Tools

  • Drain Pan
  • Jack Stands
  • Assistant
  • Floor Jack

  • Materials, Fluids, and Supplies

  • Gear Oil

  • Pliers, Cutters & misc Wrenches

  • Needle nose pliers

  • Ratchets & Related

  • Torque Wrench
  • A Piece of Pipe (for leverage)
  • Ratchet
  • 1/2 Inch Breaker Bar

  • Screwdrivers & Related

  • Pry Bar

  • Sockets - Metric

  • 22mm Socket
  • 15mm Socket
  • 21mm Socket
  • 32mm Socket

  • Wrenches - Metric

  • 14mm Wrench

There are no reviews for this item. Write Review
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

  • 2000-2001 Infiniti I30 Front CV Axle Shaft Driver Side (excluding Limited Slip Differential) TRQ CSA82193
  • 2002-2004 Infiniti I35 Front CV Axle Shaft Driver Side TRQ CSA82193
  • 2000-2001 Nissan Maxima Front CV Axle Shaft for Models with Automatic Transmission Driver Side (excluding Limited Slip Differential) TRQ CSA82193
  • 2002-2003 Nissan Maxima Front CV Axle Shaft for Models with Automatic Transmission Driver Side TRQ CSA82193
  • 2007-2008 Nissan Maxima Front CV Axle Shaft for Models with CVT Transmission Driver Side TRQ CSA82193

This part replaces:

  • Hollander 447-60966L
  • A1 Cardone 66-6192
  • TRQ CSA82193
Part #: 1AACV00085

TRQ
Brand #: CSA82193

How-to Video:

(08:58 min)