Specifications

  • Fits either LH (Driver Side) or RH (Passenger Side) FRONT
  • Brand New
    • Not remanufactured
    • No core charge
  • Overall Length: 19-1/2"
  • Direct replacement
  • Built to strict quality control standards

CV axles are designed to transmit the power from your vehicle's drivetrain to the wheels while being able to flex and pivot to the demands of the steering and suspension systems.  If your vehicle is making clicking noises at lower speeds or when making turns, it may be time to replace your CV axles with our 100% brand new assemblies.

100% New Components

For quality fit, finish, and easy installation.

Heat Treated

For longer-lasting life and consistent performance under different road conditions.

Precision Machined

And made of brand new components, held to tighter tolerances for better consistency than rebuilt parts.

Item Condition: New

WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

  1. step : Disconnecting the CV Axle (0:53)
    • Pry off the center cap with a flat blade screwdriver
    • Pull off the hub dust cover with pliers
    • Remove the 13mm axle nut
    • Have an assistant hold the tire or press the brakes
    • Remove the six 12-point, 12mm bolts that hold the CV axle to the solid axle
  2. step : Disconnecting the Strut (2:10)
    • Remove the 30mm nut bolt from the bottom of the strut
    • Tap the 30mm bolt out with a hammer
    • Pry the strut aside with a pry bar
  3. step : Removing the CV Axle (3:06)
    • Pull the CV axle past the solid axle
    • Pull the CV axle out of the wheel hub
    • Pull the CV axle out past the solid axle
  4. step : Installing the New CV Axle (3:47)
    • Slide the CV Axle into position
    • Slide the CV Axle into the wheel hub
  5. step : Reconnecting the Strut (4:19)
    • Pry the strut into the lower control arm
    • Fasten the 30mm nut and bolt onto the bottom of the strut
    • Tighten the 30mm nut and bolt to between 95 to 100 foot-pounds of torque
  6. step : Reconnecting the CV Axle (4:49)
    • Line up the CV axle with the solid axle
    • Insert the six 12-point, 12mm bolts into the CV Axle
    • Tighten the 12mm bolts to 25 foot-pounds in a crossing or star pattern
    • Fasten the 13mm nut onto the end of the axle
    • Tap on the dust cover with a hammer
    • Push on the center cap

Tools needed for replacement:

    General Tools

  • Jack Stands
  • Floor Jack
  • Assistant

  • Pliers, Cutters & misc Wrenches

  • Needle nose pliers

  • Ratchets & Related

  • A Piece of Pipe (for leverage)
  • Ratchet
  • Torque Wrench

  • Screwdrivers & Related

  • Pry Bar

  • Sockets - Metric

  • 24mm Socket
  • 30mm Socket
  • 13mm Socket
  • 12mm Socket

5.0 / 5.0
3 Reviews
5 Stars
4 Stars
3 Stars
2 Stars
1 Star
3
0
0
0
0
Great product fits perfect!
Well priced and great product fits perfect! Different end but bolt pattern fits perfect. Overall length is correct despite boots being longer. So far so good!
May 3, 2018
Purchased
6 months ago
Quality parts, perfect fit
My 06 f150 was making loud popping noises while in 4 wheel drive under a load. I assumed it was the actuator for the 4 wheel drive system. After replacing the parts and the noise still there is took the truck to a macanic and learned the transfer case was bad. But the parts from 1a Auto were great.
February 9, 2018
Purchased
8 months ago
great replacement part
Great replacement part ,order came a day early, packed well, part fit as it should
also how to videos are pricless
will continue to use 1A Auto
December 20, 2017
Purchased
10 months ago
Start typing your question and we'll check if it was already asked and answered. Learn More
Browse 1 question Browse 1 question and 4 answers
I picked up a pair of these from Advanced but they bind. I have read the factory built parts have more bearings therefore do not bind. Do yours have the same amount of bearings so no binding occurs?
Travis W on Jun 13, 2018
BEST ANSWER: I installed the axle shafts on a 2008 f150 4x4. They work great. No binding. Fit together well with wheel hub and transfer case. I never checked regarding if it had the same amount of bearings as the OEM. To me, it doesn't matter as the axles work. I replaced everything from the transfer case to the wheel hub (wheel hub actuators). I also replaced the vacuum lines and solenoid for the 4 wheel system. Purchased all at 1aauto. Came quickly, ...as ordered & works!! I very much appreciated the Tutorial Videos on YouTube by 1aauto ...instruction on installing the parts. That is why I bought from 1aauto..... the help they provided.

Vehicle Fit

Year Make Model Description
2003-2006Ford Expedition Ford Expedition Front CV Axle Shaft Driver or Passenger Side TRQ CSA82125
2004Ford F150 Truck Ford F150 Truck New Body Style Front CV Axle Shaft Driver or Passenger Side TRQ CSA82125
2005-2008Ford F150 Truck Ford F150 Truck Front CV Axle Shaft Driver or Passenger Side TRQ CSA82125
2006-2008Lincoln Mark LT Lincoln Mark LT Front CV Axle Shaft Driver or Passenger Side TRQ CSA82125
2003-2006Lincoln Navigator Lincoln Navigator Front CV Axle Shaft Driver or Passenger Side TRQ CSA82125

This part replaces:

  • Hollander 447-02746
  • A1 Cardone 66-2103
  • TRQ CSA82125
  • OE # 5L1Z3B436AA
  • OE # 2L143A327BD
Part #: 1AACV00144


Order must be placed by 4pm ET

Get it in: 2 - 4 Business Days

Want it sooner? Choose Next Day Air at Checkout

TRQ
Brand #: CSA82125

How-to Video:

(06:38 min)