Replaces
CV Axle Shaft Front - 1AACV00097
1AACV00097This axle shaft is a new, aftermarket part. It is just what you need to get your vehicle back in good working order!
Specifications:
- Fits either LH (Driver Side) or RH (Passenger Side) FRONT
- Overall Length: 21-3/16 Inch
- Outboard Spline Count: 33
- Built to strict quality control standards
- Direct replacement
- Has ABS tone ring
- Can be removed if not needed
Note: This is for one axle shaft assembly. If you need a pair, please see our other listings.
Axle shafts may need replacing for a variety of different reasons. On vehicles that do heavy work or endure other extreme use you can actually break an axle or strip the splines or teeth. More often the CV joint wears out causing noises and vibration while accelerating or turning.
Lifetime Warranty
This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.
-
step : Removing the Wheel (0:48)
- Removing the Wheel
- Loosen the lug nut covers with a 22mm socket
- Pry off the center cap with a flat blade screwdriver
- Loosen the 35mm nut but don't remove it
- Loosen the lug nuts with the vehicle on the ground
- Raise the vehicle with a floor jack
- Secure the vehicle on jack stands
- Remove the lug nuts
- Pull off the wheel
-
step : Removing the Stabilizer Link (1:32)
- Using locking pliers to clip onto the top of the stabilizer link
- Then remove 14mm bolt from bottom of the stabilizer link
- Remove the stabilizer link with a hammer or reciprocating saw
-
step : Removing the Axle (2:41)
- Use a pry bar to hold the hub in place
- Loosen and remove the 15mm bolts
- Hammer the axle over to the side to release it
- Pull it straight back and out of the wheel and down and out
-
step : Reinstalling the Axle (3:34)
- Feed the axle into the place
- Line up the back and replace the 15mm bolts
- Use a pry bar to hold the hub in place
- Torque each bolt to 65 ft/lbs
-
step : Replacing the Stabilizer Link (4:51)
- Put the stabilizer piece back into place
- Use four washers, four grommets, and a tube
- Use a jack stand to help push it through till it appears through the top
- Tighten the 14mm bolt on the stabilizer link
- Tighten until the bushings are the same diameter as the washers
-
step : Replacing the Wheel (6:18)
- Replace and tighten the 35mm nut
- Put the tire in place
- Replace and tighten each lug nut
- Torque each lug nut in a crossing pattern to 100 ft/lbs
- Torque the center hub nut to 160 ft/lbs
- Replace the hub cap and tighten the lug nut caps
Tools needed for replacement:
- Jack Stands
- Sawzall
- Vise Grip Pliers
- Ratchet
- Socket Extensions
- Torque Wrench
- Pry Bar
- 14mm Socket
- 15mm Socket
- 22mm Socket
- 35mm Socket
- 36mm Socket
General Tools
Pliers, Cutters & misc Wrenches
Ratchets & Related
Screwdrivers & Related
Sockets - Metric
- Was this review helpful? Yes (0) No (0)
- Flag as Inappropriate
- Was this review helpful? Yes (0) No (0)
- Flag as Inappropriate
Thank you
George
- Was this review helpful? Yes (0) No (1)
- Flag as Inappropriate
- Was this review helpful? Yes (0) No (1)
- Flag as Inappropriate
- Reply
- Inaccurate
- Tim K Staff on May 23, 2017
- Reply
- Inaccurate
- 1A Tech Guy Staff on May 16, 2016
Vehicle Fit
- 2002-2006 Cadillac Escalade Front CV Axle Shaft Driver or Passenger Side
- 2003-2006 Cadillac Escalade ESV Front CV Axle Shaft Driver or Passenger Side
- 2002-2006 Cadillac Escalade EXT Front CV Axle Shaft Driver or Passenger Side
- 2002-2006 Chevy Avalanche 1500 Front CV Axle Shaft Driver or Passenger Side
- 1999-2003 Chevy Silverado 1500 Front CV Axle Shaft Driver or Passenger Side (excluding Crew Cab)
- 2004-2006 Chevy Silverado 1500 Front CV Axle Shaft for Models with 6 Lug Wheels Driver or Passenger Side
- 2007 Chevy Silverado 1500 Classic Front CV Axle Shaft for Models with 6 Lug Wheels Driver or Passenger Side
- 2000-2006 Chevy Suburban 1500 Front CV Axle Shaft Driver or Passenger Side
- 2000 Chevy Tahoe Front CV Axle Shaft Driver or Passenger Side (excluding Z71 Models)
- 2001-2006 Chevy Tahoe Front CV Axle Shaft Driver or Passenger Side
- 1999-2003 GMC Sierra 1500 Front CV Axle Shaft Driver or Passenger Side (excluding Crew Cab)
- 2004-2006 GMC Sierra 1500 Front CV Axle Shaft for Models with 6 Lug Wheels Driver or Passenger Side
- 2007 GMC Sierra 1500 Classic Front CV Axle Shaft for Models with 6 Lug Wheels Driver or Passenger Side
- 2000 GMC Yukon Front CV Axle Shaft Driver or Passenger Side (excluding Denali Models)
- 2001-2006 GMC Yukon Front CV Axle Shaft Driver or Passenger Side
- 2000-2006 GMC Yukon XL 1500 Front CV Axle Shaft Driver or Passenger Side
This part replaces:
- OE # 26069244
- Hollander 447-02433
- OE # 26069252
- A1 Cardone 66-1009