These axle shafts are new, aftermarket parts. They are just what you need to get your vehicle back in good working order!

Specifications:

  • Comes as a PAIR
    • Fits both LH (Driver Side) & RH (Passenger Side) FRONT
  • Overall Length: 21-3/16 Inch
  • Outboard Spline Count: 33
  • Built to strict quality control standards
  • Direct replacements
  • Has ABS tone rings
    • Can be removed if not needed

Note: This is for two axle shaft assemblies. If you need a single, please see our other listings.

Axle shafts may need replacing for a variety of different reasons. On vehicles that do heavy work or endure other extreme use you can actually break an axle or strip the splines or teeth. More often the CV joint wears out causing noises and vibration while accelerating or turning.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

  1. step : Removing the Wheel (0:48)
    • Removing the Wheel
    • Loosen the lug nut covers with a 22mm socket
    • Pry off the center cap with a flat blade screwdriver
    • Loosen the 35mm nut but don't remove it
    • Loosen the lug nuts with the vehicle on the ground
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the lug nuts
    • Pull off the wheel
  2. step : Removing the Stabilizer Link (1:32)
    • Using locking pliers to clip onto the top of the stabilizer link
    • Then remove 14mm bolt from bottom of the stabilizer link
    • Remove the stabilizer link with a hammer or reciprocating saw
  3. step : Removing the Axle (2:41)
    • Use a pry bar to hold the hub in place
    • Loosen and remove the 15mm bolts
    • Hammer the axle over to the side to release it
    • Pull it straight back and out of the wheel and down and out
  4. step : Reinstalling the Axle (3:34)
    • Feed the axle into the place
    • Line up the back and replace the 15mm bolts
    • Use a pry bar to hold the hub in place
    • Torque each bolt to 65 ft/lbs
  5. step : Replacing the Stabilizer Link (4:51)
    • Put the stabilizer piece back into place
    • Use four washers, four grommets, and a tube
    • Use a jack stand to help push it through till it appears through the top
    • Tighten the 14mm bolt on the stabilizer link
    • Tighten until the bushings are the same diameter as the washers
  6. step : Replacing the Wheel (6:18)
    • Replace and tighten the 35mm nut
    • Put the tire in place
    • Replace and tighten each lug nut
    • Torque each lug nut in a crossing pattern to 100 ft/lbs
    • Torque the center hub nut to 160 ft/lbs
    • Replace the hub cap and tighten the lug nut caps

Tools needed for replacement:

    General Tools

  • Jack Stands
  • Sawzall

  • Pliers, Cutters & misc Wrenches

  • Vise Grip Pliers

  • Ratchets & Related

  • Ratchet
  • Socket Extensions
  • Torque Wrench

  • Screwdrivers & Related

  • Pry Bar

  • Sockets - Metric

  • 14mm Socket
  • 15mm Socket
  • 22mm Socket
  • 35mm Socket
  • 36mm Socket

4.7 / 5.0
3 Reviews
5 Stars
4 Stars
3 Stars
2 Stars
1 Stars
2
1
0
0
0
Fit, Form and Function
Fit perfectly and solved my CV Joint issues at a Grat Price!
April 23, 2017
Want to thank you all for being a awesome parts supplier great quality parts thanks
March 27, 2018
Purchased
1 month ago
only 4 stars, but not all 1A's fault
Ordered some axle shafts and 1A shipped promptly, but the parts did not arrive after 2 weeks. Opened investigation with 1A and UPS. Turns out the boxes were damaged in transit and sat at UPS facility for a week without anyone doing anything to contact me or 1A about problem. I had to call and complain and open an investigation. The problem was with UPS and not 1A. However I would suggest to 1A that if a part doesn't get delivered, perhaps they could get some software that notifies them of the issue before a customer like me has to complain.....I know.....maybe in a perfect world. 1A did offer to resend the parts but UPS found it's mistake and did deliver the boxes. The boxes were damaged, but the axle shafts inside appear to be ok. It's hard to damage a steel shaft. I'm happy with 1A but NOT with 1A's choice for a shipping vendor.
January 13, 2018
Purchased
3 months ago
Start typing your question and we'll check if it was already asked and answered. Learn More
Browse 3 questions Browse 3 questions and 7 answers
do these come already greased?
suelo_jv on Sep 28, 2017
BEST ANSWER: Yes, these are pre greased.
Where are these parts made?
John E on Apr 19, 2017
BEST ANSWER: These are made in either Taiwan, or China.
What is the sawzall used for?
Garrett D on Jun 5, 2016
BEST ANSWER: If the sway bar links are to rusted to remove than u can cut them out of the way to remove the axles and replace the links with new parts.

Vehicle Fit

  • 2002-2006 Cadillac Escalade Front CV Axle Shaft Pair
  • 2003-2006 Cadillac Escalade ESV Front CV Axle Shaft Pair
  • 2002-2006 Cadillac Escalade EXT Front CV Axle Shaft Pair
  • 2002-2006 Chevy Avalanche 1500 Front CV Axle Shaft Pair
  • 1999-2003 Chevy Silverado 1500 Front CV Axle Shaft Pair (excluding Crew Cab)
  • 2004-2006 Chevy Silverado 1500 Front CV Axle Shaft for Models with 6 Lug Wheels Pair
  • 2007 Chevy Silverado 1500 Classic Front CV Axle Shaft for Models with 6 Lug Wheels Pair
  • 2000-2006 Chevy Suburban 1500 Front CV Axle Shaft Pair
  • 2000 Chevy Tahoe Front CV Axle Shaft Pair (excluding Z71 Models)
  • 2001-2006 Chevy Tahoe Front CV Axle Shaft Pair
  • 1999-2003 GMC Sierra 1500 Front CV Axle Shaft Pair (excluding Crew Cab)
  • 2004-2006 GMC Sierra 1500 Front CV Axle Shaft for Models with 6 Lug Wheels Pair
  • 2007 GMC Sierra 1500 Classic Front CV Axle Shaft for Models with 6 Lug Wheels Pair
  • 2000 GMC Yukon Front CV Axle Shaft Pair (excluding Denali Models)
  • 2001-2006 GMC Yukon Front CV Axle Shaft Pair
  • 2000-2006 GMC Yukon XL 1500 Front CV Axle Shaft Pair

This part replaces:

  • OE # 26069244
  • Hollander 447-02433
  • OE # 26069252
Part #: 1AACS00104



How-to Video:

(07:40 min)